Паспорта безопасности и отчёты заводских испытаний
Паспорта безопасности и отчёты заводских испытаний
Verified SDS (16-section GHS format), factory inspection standards and technical data sheets for the complete FanChu industrial lubricant portfolio. All content is provided in English, Russian and Spanish.
Back to Technical Documentation & Product DataPart A — Common Safety Provisions (SDS sections 1–16)
These 16 sections are common to all 93 models. Model-specific composition, physical properties and inspection criteria are listed in Part B.
01Manufacturer / Supplier InformationИнформация о производителе и поставщикеInformación del fabricante / proveedor
Manufacturer: Guangzhou FanChu Lubricant Technology Co., Ltd. | Address: No. 8 Xingda Road, Yunpu Industrial Zone, Kaichuang Avenue North, Huangpu District, Guangzhou, China | Tel: +86-20-32050123 | Fax: +86-20-32035369 | Emergency contact: +86-20-32050123.
Производитель: Guangzhou FanChu Lubricant Technology Co., Ltd. | Адрес: Китай, Гуанчжоу, район Хуанпу, Северный проспект Кайчуан, промышленная зона Юньпу, ул. Синда, д. 8 | Тел.: +86-20-32050123 | Факс: +86-20-32035369 | Экстренная связь: +86-20-32050123.
Fabricante: Guangzhou FanChu Lubricant Technology Co., Ltd. | Dirección: No. 8 Xingda Road, Zona Industrial Yunpu, Kaichuang Avenue North, Distrito Huangpu, Guangzhou, China | Tel.: +86-20-32050123 | Fax: +86-20-32035369 | Contacto de emergencia: +86-20-32050123.
02Composition / Information on IngredientsСостав / информация о компонентахComposición / información sobre los componentes
The formulation is a blend of refined base oils and functional additives. The exact component names, chemical identities and concentration ranges for each model are listed in the product-specific annex below. No substance in this product is classified as a CMR category 1A/1B at or above the applicable cut-off level.
Препарат представляет собой смесь очищенных базовых масел и функциональных присадок. Точные наименования компонентов, химическая природа и диапазоны концентраций для каждой модели приведены в индивидуальном приложении к продукту ниже. Ни одно из веществ не классифицируется как CMR категории 1A/1B на уровне пороговых концентраций или выше.
La formulación es una mezcla de aceites base refinados y aditivos funcionales. Los nombres exactos de los componentes, su identidad química y los rangos de concentración de cada modelo se indican en el anexo específico del producto más abajo. Ninguna sustancia está clasificada como CMR de categoría 1A/1B por encima de los límites aplicables.
03Hazards IdentificationИдентификация опасностейIdentificación de peligros
Eyes: the liquid is an eye irritant and may cause pain and redness. Skin: non-irritating under normal contact; prolonged or repeated exposure may cause itching. Inhalation: excessive oil mist, fumes or vapour may irritate the nose and throat and cause coughing. Ingestion: may cause nausea. Environment: no significant bioaccumulation. Physical/chemical: chemically stable; solubility in water depends on the formulation (see the product annex). Special hazards: none.
Глаза: жидкость вызывает раздражение, возможны боль и покраснение. Кожа: при обычном контакте не раздражает; длительное или повторное воздействие может вызвать зуд. Вдыхание: избыток масляного тумана, паров или дыма может раздражать носоглотку и вызывать кашель. Проглатывание: возможна тошнота. Окружающая среда: заметной биоаккумуляции нет. Физико-химические свойства: химически стабилен; растворимость в воде зависит от состава (см. приложение к продукту). Особые опасности: отсутствуют.
Ojos: el líquido es irritante y puede causar dolor y enrojecimiento. Piel: no irritante en contacto normal; la exposición prolongada o repetida puede producir picor. Inhalación: el exceso de niebla de aceite, humos o vapores puede irritar nariz y garganta y provocar tos. Ingestión: puede causar náuseas. Medio ambiente: sin bioacumulación significativa. Físico/químico: químicamente estable; la solubilidad en agua depende de la formulación (véase el anexo del producto). Peligros especiales: ninguno.
04First-Aid MeasuresМеры первой помощиPrimeros auxilios
Skin contact: wash as soon as possible with clean or warm water. Eye contact: hold the eyes open and flush with plenty of water; if redness, pain or discomfort persists, seek medical attention. Ingestion: rinse the mouth thoroughly with water; in case of accident seek medical attention and do NOT induce vomiting. Inhalation: move to fresh air; if discomfort continues, seek medical attention. Medical advice: treatment should be symptomatic and supportive.
При попадании на кожу: как можно скорее промыть чистой или тёплой водой. При попадании в глаза: держать глаза открытыми и обильно промыть водой; при сохраняющемся покраснении, боли или дискомфорте обратиться к врачу. При проглатывании: тщательно прополоскать рот водой; при несчастном случае обратиться к врачу, НЕ вызывать рвоту. При вдыхании: вывести на свежий воздух; при сохраняющемся недомогании обратиться к врачу. Медицинские рекомендации: лечение симптоматическое и поддерживающее.
Contacto con la piel: lavar lo antes posible con agua limpia o templada. Contacto con los ojos: mantener los ojos abiertos y enjuagar con abundante agua; si persiste enrojecimiento, dolor o molestia, acudir al médico. Ingestión: enjuagar bien la boca con agua; en caso de accidente acudir al médico y NO provocar el vómito. Inhalación: trasladar al aire fresco; si persiste el malestar, acudir al médico. Recomendación médica: tratamiento sintomático y de soporte.
05Fire-Fighting MeasuresМеры пожаротушенияMedidas de lucha contra incendios
Suitable extinguishing media: dry chemical powder, carbon dioxide, foam. Specific hazards: none. Fire-fighting procedure: (1) fight the fire from a safe distance or a protected position; (2) stay upwind to avoid hazardous vapours and toxic decomposition products; (3) stop the leak before extinguishing — if the leak cannot be stopped and there is no danger to the surroundings, allow the fire to burn out, because an unstopped leak may form an explosive vapour/air mixture and re-ignite; (4) isolate unignited material and protect personnel; (5) remove product from the fire area if safe to do so; (6) cool exposed, non-leaking containers with a water spray; (7) if the leak is not ignited, use a water spray to disperse vapours and protect personnel stopping the leak; (8) evacuate the area where possible and allow the fire to burn out; (9) keep away from flammable and explosive materials; (10) firefighters must wear self-contained breathing apparatus, fire-resistant clothing and protective gloves.
Пригодные средства тушения: сухой химический порошок, диоксид углерода, пена. Особые опасности: отсутствуют. Порядок тушения: (1) тушить с безопасного расстояния или из укрытия; (2) находиться с наветренной стороны во избежание воздействия опасных паров и токсичных продуктов разложения; (3) перед тушением перекрыть утечку — если утечку нельзя устранить и окружение безопасно, дать огню выгореть, так как неустранённая утечка может образовать взрывоопасную паровоздушную смесь и привести к повторному возгоранию; (4) изолировать негорящие материалы и защитить персонал; (5) при безопасности вынести продукт из зоны пожара; (6) охлаждать водяной пылью подвергшиеся нагреву, но не протекающие ёмкости; (7) если утечка не воспламенилась, распылять воду для рассеивания паров и защиты персонала, устраняющего утечку; (8) по возможности эвакуироваться и дать огню выгореть; (9) держаться вдали от легковоспламеняющихся и взрывчатых материалов; (10) пожарные должны использовать автономный дыхательный аппарат, огнезащитную одежду и защитные перчатки.
Medios de extinción adecuados: polvo químico seco, dióxido de carbono, espuma. Peligros específicos: ninguno. Procedimiento: (1) combatir el fuego desde una distancia segura o posición protegida; (2) situarse a barlovento para evitar vapores peligrosos y productos de descomposición tóxicos; (3) detener la fuga antes de extinguir — si no puede detenerse y no hay peligro para el entorno, dejar que el fuego se consuma, ya que una fuga no controlada puede formar una mezcla explosiva vapor/aire y reignirse; (4) aislar el material no inflamado y proteger al personal; (5) retirar el producto de la zona si es seguro; (6) enfriar con agua pulverizada los envases expuestos que no presenten fugas; (7) si la fuga no se ha inflamado, usar agua pulverizada para dispersar vapores y proteger al personal; (8) evacuar cuando sea posible y dejar consumir el fuego; (9) mantener alejados materiales inflamables y explosivos; (10) los bomberos deben usar equipo de respiración autónomo, ropa ignífuga y guantes protectores.
06Accidental Release MeasuresМеры при случайном выбросеMedidas en caso de vertido accidental
Personal precautions: none specific. Environmental precautions: prevent the product from entering drains, sewers and watercourses. Clean-up: absorb with an inert absorbent, or contain and remove by the most effective available method.
Меры личной предосторожности: специальных мер не требуется. Меры защиты окружающей среды: не допускать попадания в дренаж, канализацию и водотоки. Способ уборки: собрать инертным адсорбентом либо локализовать и удалить наиболее эффективным доступным способом.
Precauciones personales: ninguna específica. Precauciones ambientales: evitar la entrada en desagües, alcantarillado y cursos de agua. Limpieza: absorber con un absorbente inerte o contener y retirar por el método más eficaz disponible.
07Handling and StorageПравила обращения и храненияManipulación y almacenamiento
Safe handling: avoid breathing oil vapour and oil mist; use only in well-ventilated areas; avoid repeated or prolonged skin contact; maintain good personal hygiene; do not ingest. Storage: no special precautions required, but avoid direct sunlight and exposure to rain.
Безопасное обращение: не вдыхать пары и масляный туман; использовать только в хорошо проветриваемых помещениях; избегать повторного или длительного контакта с кожей; соблюдать правила личной гигиены; не проглатывать. Хранение: специальных мер не требуется, однако следует избегать прямых солнечных лучей и попадания дождя.
Manipulación segura: evitar inhalar vapores y niebla de aceite; usar solo en zonas bien ventiladas; evitar el contacto repetido o prolongado con la piel; mantener una buena higiene personal; no ingerir. Almacenamiento: sin precauciones especiales, aunque conviene evitar la luz solar directa y la lluvia.
08Exposure Controls / Personal ProtectionКонтроль воздействия / индивидуальная защитаControles de exposición / protección personal
Engineering controls: ensure adequate general ventilation; local exhaust ventilation is recommended. Avoid inhaling oil vapour, fumes and mist generated during use.
Технические меры: обеспечить достаточную общеобменную вентиляцию; рекомендуется местная вытяжная вентиляция. Избегать вдыхания паров, дыма и масляного тумана, образующихся при использовании.
Controles de ingeniería: garantizar una ventilación general adecuada; se recomienda ventilación por extracción local. Evitar inhalar vapores, humos y niebla de aceite generados durante el uso.
09Physical and Chemical PropertiesФизико-химические свойстваPropiedades físicas y químicas
Physical state, colour, pH (5% dilution), density at 20 °C and other measured values are model-specific and are listed for each product in the annex below. All values are typical values from factory inspection, not guaranteed specification limits unless stated otherwise.
Физическое состояние, цвет, pH (5%-ный раствор), плотность при 20 °C и другие измеряемые показатели зависят от модели и приведены для каждого продукта в приложении ниже. Все значения являются типичными результатами заводского контроля и не являются гарантированными предельными нормами, если не указано иное.
El estado físico, color, pH (dilución al 5 %), densidad a 20 °C y demás valores medidos dependen del modelo y se indican para cada producto en el anexo inferior. Todos los valores son típicos del control de fábrica y no constituyen límites de especificación garantizados salvo indicación expresa.
10Stability and ReactivityСтабильность и реакционная способностьEstabilidad y reactividad
The product is stable and no hazardous reaction is expected under normal conditions of use. Hazardous polymerisation will not occur. Conditions to avoid: high-temperature heat sources. Hazardous decomposition products: none.
Продукт стабилен; при обычных условиях применения опасные реакции не ожидаются. Опасная полимеризация не происходит. Чего избегать: высокотемпературных источников тепла. Опасные продукты разложения: отсутствуют.
El producto es estable y no se esperan reacciones peligrosas en condiciones normales de uso. No se produce polimerización peligrosa. Condiciones a evitar: fuentes de calor a alta temperatura. Productos de descomposición peligrosos: ninguno.
11Toxicological InformationТоксикологическая информацияInformación toxicológica
Eyes: accidental contact causes temporary irritation and redness but no more serious injury. Skin: short-term or occasional contact does not cause harm. Ingestion: small accidental amounts are not harmful; large amounts may cause nausea and diarrhoea. Inhalation: oil vapour, fumes or mist may irritate the eyes, nose and throat in sensitive individuals. Exposure to vapours or smoke from thermal decomposition products may cause discomfort.
Глаза: при случайном контакте — временное раздражение и покраснение без более серьёзных повреждений. Кожа: кратковременный или эпизодический контакт не наносит вреда. Проглатывание: небольшое случайное количество безвредно; большое количество может вызвать тошноту и диарею. Вдыхание: пары, дым или туман масла могут раздражать глаза, нос и горло у чувствительных лиц. Воздействие паров или дыма продуктов термического разложения может вызвать недомогание.
Ojos: el contacto accidental produce irritación y enrojecimiento temporales sin lesiones más graves. Piel: el contacto breve u ocasional no causa daño. Ingestión: pequeñas cantidades accidentales no son nocivas; cantidades grandes pueden causar náuseas y diarrea. Inhalación: los vapores, humos o niebla de aceite pueden irritar ojos, nariz y garganta en personas sensibles. La exposición a vapores o humos de productos de descomposición térmica puede causar malestar.
12Ecological InformationЭкологическая информацияInformación ecológica
Environmental assessment: contains mineral oil, which can deplete oxygen in aquatic environments; use and dispose of the product strictly in accordance with this safety data sheet. Mobility: free-flowing liquid; solubility in water depends on the formulation. Bioaccumulative potential: no evidence of bioaccumulation. Ecotoxicity: some toxicity to aquatic organisms.
Оценка воздействия: содержит минеральное масло, способное снижать содержание кислорода в водной среде; использовать и утилизировать строго в соответствии с настоящим паспортом безопасности. Подвижность: текучая жидкость; растворимость в воде зависит от состава. Потенциал биоаккумуляции: признаков биоаккумуляции не выявлено. Экотоксичность: умеренная токсичность для водных организмов.
Evaluación ambiental: contiene aceite mineral, que puede reducir el oxígeno en medios acuáticos; utilizar y eliminar estrictamente según esta ficha de datos de seguridad. Movilidad: líquido fluido; la solubilidad en agua depende de la formulación. Potencial de bioacumulación: sin evidencia de bioacumulación. Ecotoxicidad: cierta toxicidad para organismos acuáticos.
13Disposal ConsiderationsРекомендации по утилизацииConsideraciones sobre eliminación
Dispose of waste in accordance with a waste-recovery contract concluded under local regulations. Unused product may be recovered for reuse. Used or contaminated product must be handled by a treatment facility licensed by national and local authorities; do not discharge into drains or sewers.
Утилизировать отходы в соответствии с договором на переработку, заключённым по местным нормативам. Неиспользованный продукт может быть возвращён в оборот. Использованный или загрязнённый продукт подлежит передаче на очистные сооружения, имеющие разрешение национальных и местных органов; сброс в канализацию и дренаж недопустим.
Eliminar los residuos conforme a un contrato de recuperación suscrito según la normativa local. El producto sin usar puede recuperarse para su reutilización. El producto usado o contaminado debe gestionarse en una planta autorizada por las autoridades nacionales y locales; no verter en desagües ni alcantarillado.
14Transport InformationИнформация о транспортировкеInformación sobre el transporte
Not classified as dangerous goods for transport (ADR / IMDG / IATA).
Не классифицируется как опасный груз при перевозке (ADR / IMDG / IATA).
No clasificado como mercancía peligrosa para el transporte (ADR / IMDG / IATA).
15Regulatory InformationНормативная информацияInformación reglamentaria
Applicable regulations: Work Safety Law of the People's Republic of China; Law on Prevention and Control of Occupational Diseases; Regulations on the Safety Management of Hazardous Chemicals. Product classification and labelling follow GB 30000 series (GHS) and GB/T 16483.
Применимые нормативные акты: Закон КНР «О безопасности производства»; Закон КНР «О профилактике и контроле профессиональных заболеваний»; Правила управления безопасностью опасных химических веществ. Классификация и маркировка соответствуют серии GB 30000 (GHS) и GB/T 16483.
Normativa aplicable: Ley de Seguridad en el Trabajo de la República Popular China; Ley de Prevención y Control de Enfermedades Profesionales; Reglamento de Gestión de Seguridad de Productos Químicos Peligrosos. La clasificación y el etiquetado siguen la serie GB 30000 (SGA/GHS) y GB/T 16483.
16Other InformationПрочая информацияOtra información
References: Catalogue of Hazardous Chemicals (2015 edition); GB 39800.1-2020 Specification for the provision of personal protective equipment; GB 12801-2008 General principles for safety and health requirements in production processes. Disclaimer: the data above have been compiled from reference sources and are believed to be correct, but errors may occur; the user is responsible for judging suitability under actual conditions of use. This information is revised and improved periodically.
Ссылки: Каталог опасных химических веществ (изд. 2015); GB 39800.1-2020 «Требования к обеспечению средствами индивидуальной защиты»; GB 12801-2008 «Общие принципы требований безопасности и гигиены в производственных процессах». Оговорка: данные составлены по справочным источникам и считаются достоверными, однако возможны неточности; пользователь самостоятельно оценивает применимость с учётом фактических условий. Информация периодически пересматривается и уточняется.
Referencias: Catálogo de Productos Químicos Peligrosos (edición 2015); GB 39800.1-2020 Especificación para la dotación de equipos de protección individual; GB 12801-2008 Principios generales de requisitos de seguridad e higiene en procesos productivos. Descargo: los datos se han recopilado de fuentes de referencia y se consideran correctos, pero pueden existir errores; el usuario debe juzgar la idoneidad según las condiciones reales de uso. Esta información se revisa y mejora periódicamente.
Part B — Product-Specific Technical Dossiers
Each dossier lists composition, physical/chemical properties, factory inspection criteria and TDS specifications extracted from the original Chinese documents. Values and units are reproduced verbatim; field names and technical terms are localised.
Factory inspection reports are issued as blank standard forms: the acceptance criteria are published here, while measured batch results are recorded on the certificate of analysis supplied with each shipment.
Emulsified Oils
SW-013SW-013 Rust-Preventive Emulsified OilTDSSDSCOA
Technical Overview
Nitrite- and phenol-free rust-preventive emulsifiable fluid for cast iron and carbon steel. Stable, long sump life with superior corrosion protection, cooling and lubricity.
Водосмешиваемая эмульгируемая СОЖ для обработки чугуна, углеродистой стали и алюминиевых сплавов; отличается длительным сроком службы ванны и надёжной межоперационной защитой от коррозии.
Fluido de corte emulsionable miscible en agua para fundición, acero al carbono y aleaciones de aluminio, con larga vida útil del baño y protección anticorrosiva fiable entre operaciones.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Lubricity agent | Fatty acid ester | 0-12% |
| Alkali buffer | Alkanolamine | 0-10% |
| Surfactant | Fatty alcohol ethoxylate | 0-10% |
| Emulsifier | Oleate ester | 0-8% |
| Rust inhibitor | Petroleum sulfonate | 0-8% |
| Base oil | Mineral oil | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Red-brown |
| pH value | 5% / 9.2-9.6 |
| Density@ | 20℃ g/cm3 0.92±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 9.2-9.6 |
| Foam tendency,10min/ml | ≤2 |
| Corrosion test h (55±2℃full immersion) | Steel strip 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | 0.5 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Brown-red clear liquid |
| Appearance, 5%wt.Dilution | Visual | Milky opaque liquid |
| pH Value, 5%wt. | pH meter | 9.2-9.6 |
| Emulsion Stability@15-35°C,24h, Soap | SH/0365 | <= 0.5 |
| Emulsion Stability@15-35°C,24h, Oil | SH/0365 | None |
| Emulsion Rust Prevention@35±2°C, Cast Iron Chips, Single Chip, 24h | GB/T6144 | Grade A |
| Emulsion Rust Prevention@35±2°C, Cast Iron Chips, Stacked Chips, 8h | GB/T6144 | Grade A |
| Emulsion Corrosion Test@55±2°C, Full Immersion, Steel Strip, 24h | GB/T6144 | Grade A |
SW-014SW-014 Aluminum Alloy Emulsified OilTDSSDSCOA
Technical Overview
Emulsifiable fluid engineered specifically for aluminum alloys, delivering stable emulsion, strong lubricity and detergency with extended service life.
Водосмешиваемая эмульгируемая СОЖ для обработки чугуна, углеродистой стали и алюминиевых сплавов; отличается длительным сроком службы ванны и надёжной межоперационной защитой от коррозии.
Fluido de corte emulsionable miscible en agua para fundición, acero al carbono y aleaciones de aluminio, con larga vida útil del baño y protección anticorrosiva fiable entre operaciones.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Corrosion inhibitor | amine carboxylate | 0-10% |
| Lubricity agent | Fatty acid ester | 0-10% |
| Alkali buffer | Alkanolamine | 0-10% |
| Surfactant | Fatty alcohol ethoxylate | 0-10% |
| Rust inhibitor | Petroleum sulfonate | 0-10% |
| Base oil | Mineral oil | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Red-brown |
| pH value | 5% / 8.80-9.20 |
| Density@ | 20℃ g/cm3 0.92±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,10min/ml | ≤2 |
| Corrosion test h (55±2℃full immersion) | Steel strip 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | 0.5 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Brown-red clear liquid |
| Appearance, 5%wt.Dilution | Visual | Milky opaque liquid |
| pH Value, 5%wt. | pH meter | 8.8-9.2 |
| Emulsion Stability@15-35°C,24h, Soap | SH/0365 | <= 0.5 |
| Emulsion Stability@15-35°C,24h, Oil | SH/0365 | None |
| Emulsion Corrosion Test@55±2°C, Full Immersion, Steel Strip, 24h | SH/0365 | Pass |
| Emulsion Corrosion Test@55±2°C, Full Immersion, Copper Strip, 6h | SH/0365 | Pass |
| Emulsion Corrosion Test@55±2°C, Full Immersion, Aluminum Strip, 4h | SH/T0365 | Pass |
SW-015SW-015 Extreme-Pressure Emulsified OilTDSSDSCOA
Technical Overview
Extreme-pressure emulsifiable oil blended with premium emulsifiers, lubricity agents and rust inhibitors for balanced lubrication, cooling, cleaning and anti-rust performance.
Водосмешиваемая эмульгируемая СОЖ для обработки чугуна, углеродистой стали и алюминиевых сплавов; отличается длительным сроком службы ванны и надёжной межоперационной защитой от коррозии.
Fluido de corte emulsionable miscible en agua para fundición, acero al carbono y aleaciones de aluminio, con larga vida útil del baño y protección anticorrosiva fiable entre operaciones.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Alkali buffer | Alkanolamine | 10-20% |
| Lubricity agent | Fatty acid ester | 0-15% |
| Base oil | Mineral oil | 45-70% |
| Surfactant | alcohol ether carboxylic acid | 0-15% |
| Rust inhibitor | Organic acid | 0-10% |
| Diluent | Water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow |
| pH value | 5% / 8.8-9.2 |
| Density@ | 20℃ g/cm3 0.95±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | >70 |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,10min/ml | ≤2 |
| Corrosion test h (55±2℃full immersion) | Steel strip 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | 0.5 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Yellow clear liquid |
| Appearance, 5%wt.Dilution | Visual | Uniform emulsion |
| pH Value, 5%wt. | pH meter | 8.8-9.2 |
| Refractometer Reading | Refractometer | > 70 |
| Emulsion Stability@15-35°C,24h, Soap | SH/T0365 | <= 0.5 |
| Emulsion Stability@15-35°C,24h, Oil | SH/T0365 | None |
| Rust Prevention, 5%wt (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Emulsion Corrosion Test@55±2°C, Full Immersion, Steel Strip, 24h | GB/T6144 | Grade A |
SW-021SW-021 Tapping FluidTDSSDSCOA
Technical Overview
High-efficiency water-soluble tapping fluid with lubricity additives, non-ferrous corrosion inhibitors and foam suppressants; heavy-metal free.
Водосмешиваемая эмульгируемая СОЖ для обработки чугуна, углеродистой стали и алюминиевых сплавов; отличается длительным сроком службы ванны и надёжной межоперационной защитой от коррозии.
Fluido de corte emulsionable miscible en agua para fundición, acero al carbono y aleaciones de aluminio, con larga vida útil del baño y protección anticorrosiva fiable entre operaciones.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | 40-50% |
| Extreme-pressure additive | EP additive package | 10-20% |
| Lubricity agent | Fatty acid amide | 10-20% |
| Surfactant | alcohol ether carboxylic acid | 3-8% |
| Rust inhibitor | Organic acid | 3-8% |
| Deionised water | Deionised water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Brown-yellow or yellow |
| pH value | 5% / 8.8-9.2 |
| Density@ | 20℃ g/cm3 0.98±0.05 Solubility / Soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | >70 |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,10min/ml | ≤2 |
| Corrosion test h (55±2℃full immersion) | Steel strip 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | 0.5 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Refractometer Reading | Refractometer | > 70 |
| pH Value, 5%wt. | pH meter | 8.8-9.2 |
| 5%DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (55°C±2°C), h | Steel strip | GB/T6144 |
| Corrosion (55°C±2°C), h | Copper | GB/T6144 |
| Corrosion (55°C±2°C), h | LY12 aluminum | GB/T6144 |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
Fully Synthetic Cutting & Grinding Fluids
SW-200SW-200 Magnesium-Aluminum Alloy Cutting FluidTDSSDSCOA
Technical Overview
Full-synthetic water-soluble cutting fluid for magnesium-aluminum alloys. Heavy-metal and nitrite free, with strong lubricity, fast chip settling and excellent cooling.
Полностью синтетическая водорастворимая СОЖ для резки и шлифования; не содержит минерального масла, нитритов и тяжёлых металлов, обеспечивает высокую чистоту обработки.
Fluido de corte y rectificado totalmente sintético y soluble en agua, sin aceite mineral, nitritos ni metales pesados, que aporta gran limpieza de mecanizado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Water | Balance |
| Alkali buffer | Alkanolamine | 0-20% |
| Lubricity agent | Polyether polyol | 0-10% |
| Lubricity agent | Glycerol | 0-10% |
| Rust inhibitor | Organic acid | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless |
| pH value | 5% / 8.8-9.2 |
| Density@ | 20℃ g/cm3 1.05±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | 28-30 |
| Transparency | Clear |
| Refractive index | Report value |
| pH value | 8.9-9.3 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Rust prevention (5%,18-28℃,cast iron chips2h) | 0grade |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Refractometer Reading | Refractometer | 28-30 |
| pH Value, 5%wt. | pH meter | 8.9-9.3 |
| Rust Prevention, 5%wt (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
| Nitrite, mg/L | Nitrite test strip | None |
SW-210SW-210 Rust-Preventive Grinding FluidTDSSDSCOA
Technical Overview
Full-synthetic water-soluble grinding fluid built on water-soluble rust inhibitors and anti-wear agents; free of sulphur, phosphorus, chlorine and heavy-metal ions.
Полностью синтетическая водорастворимая СОЖ для резки и шлифования; не содержит минерального масла, нитритов и тяжёлых металлов, обеспечивает высокую чистоту обработки.
Fluido de corte y rectificado totalmente sintético y soluble en agua, sin aceite mineral, nitritos ni metales pesados, que aporta gran limpieza de mecanizado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Surfactant | Polyether polyol | 0-10% |
| Rust inhibitor | Reaction product of organic amines and organic acids | 0-30% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless-Light yellow |
| pH value | 5% / 8.9-9.3 |
| Density@ | 20℃ g/cm3 1.05±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | 28-30 |
| Transparency | Clear |
| Refractive index | Report value |
| pH value | 8.9-9.3 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Rust prevention (5%,18-28℃,cast iron chips2h) | 0grade |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Colorless to light-yellow clear liquid |
| Appearance, 5%wt.Dilution | Visual | Colorless clear liquid |
| Refractometer Reading | Refractometer | 28-30 |
| pH Value, 5%wt. | pH meter | 8.9-9.3 |
| Rust Prevention, 5%wt (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
SW-240KNSW-240KN Precision Grinding FluidTDSSDSCOA
Technical Overview
Full-synthetic water-soluble precision grinding fluid with lubricity and rust inhibitors; free of heavy metals, sodium nitrite and phenols.
Полностью синтетическая водорастворимая СОЖ для резки и шлифования; не содержит минерального масла, нитритов и тяжёлых металлов, обеспечивает высокую чистоту обработки.
Fluido de corte y rectificado totalmente sintético y soluble en agua, sin aceite mineral, nitritos ni metales pesados, que aporta gran limpieza de mecanizado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Lubricity agent | Polyether polyol | 0-10% |
| Alkali buffer | Alkanolamine | 0-20% |
| Rust inhibitor | Organic acid | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Clear liquid |
| pH value | 5% / 8.9-9.3 |
| Density@ | 20℃ g/cm3 1.02±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | 41-42 |
| Transparency | Clear |
| Refractive index | Report value |
| pH value | 8.9-9.3 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Rust prevention (5%,18-28℃,cast iron chips2h) | 0grade |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Clear liquid |
| Appearance, 5%wt.Dilution | Visual | Colorless clear liquid |
| Refractometer Reading | Refractometer | 41-42 |
| pH Value, 5%wt. | pH meter | 8.9-9.3 |
| Rust Prevention, 5%wt (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
| Nitrite, mg/L | Nitrite test strip | None |
SW-242SW-242 Aluminum Alloy Cutting FluidTDSSDSCOA
Technical Overview
Full-synthetic water-soluble cutting fluid optimized for aluminum alloys, providing excellent lubricity and improved workpiece surface finish.
Полностью синтетическая водорастворимая СОЖ для резки и шлифования; не содержит минерального масла, нитритов и тяжёлых металлов, обеспечивает высокую чистоту обработки.
Fluido de corte y rectificado totalmente sintético y soluble en agua, sin aceite mineral, nitritos ni metales pesados, que aporta gran limpieza de mecanizado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Dispersant | Organic acid | 0-5% |
| Alkali buffer | Alkanolamine | 10-20% |
| Rust inhibitor | Organic acid | 5-10% |
| Diluent | Water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow-Yellow Diluted-fluid appearance / Clear-Semi-transparent |
| pH value | 5% / 7.5-8.5 Solubility / Fully soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | 40-44 |
| Transparency | Clear or semi-transparent |
| Refractive index | Report value |
| pH value | 7.5-8.0 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Rust prevention (5%,18-28℃,cast iron chips2h) | 0grade |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Colorless to light-yellow clear liquid |
| Refractometer Reading | Refractometer | 40-44 |
| pH Value, 5%wt. | pH meter | 7.5-8.0 |
| 10%DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (6061 Aluminum, 8h) | GB/T6144 | Grade A |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
SW-250SW-250 General-Purpose Cutting FluidTDSSDSCOA
Technical Overview
Full-synthetic water-soluble cutting fluid free of sulphur, phosphorus and chlorine additives, with balanced lubrication, cooling, cleaning and rust protection.
Полностью синтетическая водорастворимая СОЖ для резки и шлифования; не содержит минерального масла, нитритов и тяжёлых металлов, обеспечивает высокую чистоту обработки.
Fluido de corte y rectificado totalmente sintético y soluble en agua, sin aceite mineral, nitritos ni metales pesados, que aporta gran limpieza de mecanizado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Lubricity agent | Synthetic ester | 0-15% |
| Lubricity agent | Glycerol | 0-10% |
| Alkali buffer | Alkanolamine | 0-20% |
| Rust inhibitor | Organic acid | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Brown-yellow |
| pH value | 5% / 8.9-9.3 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | 35-38 |
| Transparency | Clear |
| Refractive index | Report value |
| pH value | 8.8-9.3 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Rust prevention (5%,18-28℃,cast iron chips2h) | 0grade |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Yellow clear liquid |
| Appearance, 5%wt.Dilution | Visual | Clear liquid |
| Refractometer Reading | Refractometer | 35-38 |
| pH Value, 5%wt. | pH meter | 8.8-9.3 |
| Rust Prevention, 5%wt (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Defoaming Rate, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
| Nitrite, mg/L | Nitrite test strip | None |
SW-258SW-258 Rust-Preventive Cutting FluidTDSSDSCOA
Technical Overview
Premium water-soluble cutting fluid formulated for cast iron, alloy steel and carbon steel with advanced lubricity and rust-inhibitor packages.
Полностью синтетическая водорастворимая СОЖ для резки и шлифования; не содержит минерального масла, нитритов и тяжёлых металлов, обеспечивает высокую чистоту обработки.
Fluido de corte y rectificado totalmente sintético y soluble en agua, sin aceite mineral, nitritos ni metales pesados, que aporta gran limpieza de mecanizado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Alkali buffer | Alkanolamine | 0-20% |
| Lubricity agent | Synthetic ester | 0-10% |
| Rust inhibitor | Organic acid | 0-10% |
| Glycerol | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear yellow Diluted fluid |
| Appearance | Colourless and clear |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | 29-31 |
| Transparency | Clear |
| Refractive index | Report value |
| pH value | 8.8-9.3 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Rust prevention (5%,18-28℃,cast iron chips2h) | 0grade |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Bright clear liquid |
| Appearance, 5%wt.Dilution | pH meter | Clear liquid |
| Refractometer Reading | Refractometer | 29-31 |
| pH Value, 5%wt. | GB/T 6144 | 8.8-9.3 |
| 3%DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
SW-280SW-280 General-Purpose Cutting FluidTDSSDSCOA
Technical Overview
High-efficiency full-synthetic water-soluble cutting fluid with lubricity, rust inhibitors and foam suppressants; free of heavy metals, sodium nitrite and phenols.
Полностью синтетическая водорастворимая СОЖ для резки и шлифования; не содержит минерального масла, нитритов и тяжёлых металлов, обеспечивает высокую чистоту обработки.
Fluido de corte y rectificado totalmente sintético y soluble en agua, sin aceite mineral, nitritos ni metales pesados, que aporta gran limpieza de mecanizado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Alkali buffer | Alkanolamine | 10-20% |
| Lubricity agent | Fatty acid ester | 0-10% |
| Rust inhibitor | Organic acid | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear-Semi-transparent liquid |
| pH value | 5% / 8.8-9.2 Solubility / Readily soluble in water |
| Density@ | 20℃ g/cm3 1.02±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | 28-30 |
| Transparency | Semi-transparent |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Rust prevention (5%,18-28℃,cast iron chips2h) | 0grade |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Translucent to clear liquid |
| Appearance, 5%wt.Dilution | Visual | Translucent liquid |
| Refractometer Reading | Refractometer | 28-30 |
| pH Value, 5%wt. | pH meter | 8.8-9.2 |
| Rust Prevention (5%, 18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion, (LY12 Aluminum, 55°C±2°C, 8h) | GB/T 6144 | Grade A, no corrosion |
| Corrosion, (Copper, 55°C±2°C, 8h) | GB/T 6144 | Grade A, no corrosion |
| Nitrite, mg/L | Nitrite test strip | None |
SW-285SW-285 Glass Grinding FluidTDSSDSCOA
Technical Overview
Full-synthetic grinding fluid for glass, delivering lubrication, cooling, cleaning and anti-redeposition performance that reduces edge chipping, scratches and cracking.
Полностью синтетическая водорастворимая СОЖ для резки и шлифования; не содержит минерального масла, нитритов и тяжёлых металлов, обеспечивает высокую чистоту обработки.
Fluido de corte y rectificado totalmente sintético y soluble en agua, sin aceite mineral, nitritos ni metales pesados, que aporta gran limpieza de mecanizado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Lubricity agent | Polyol | 0-30% |
| Alkali buffer | Alkanolamine | 0-20% |
| Corrosion inhibitor | ammonium carboxylate | 0-10% |
| Rust inhibitor | Organic acid | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless PH value 5% / 8.5-9.0 |
| Density@ | 20℃ g/cm3 1.03±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Transparency | Clear |
| Refractive index | Report value |
| pH value | 8.5-9.0 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Rust prevention (5%,18-28℃,cast iron chips2h) | 0grade |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Colorless clear liquid |
| Appearance, 5%wt.Dilution | Visual | Colorless clear liquid |
| pH Value, 5%wt. | pH meter | 8.5-9.0 |
| Rust Prevention, (Cast Iron, 35°C±2°C, RH>95%; Single Chip24h) | GB/T 6144 | Grade A |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
| Nitrite, mg/L | Nitrite test strip | None |
SW-400SW-400 Cemented Carbide Grinding FluidTDSSDSCOA
Technical Overview
New-generation eco-friendly full-synthetic grinding fluid purpose-built for tungsten carbide and hard-metal grinding applications.
Полностью синтетическая водорастворимая СОЖ для резки и шлифования; не содержит минерального масла, нитритов и тяжёлых металлов, обеспечивает высокую чистоту обработки.
Fluido de corte y rectificado totalmente sintético y soluble en agua, sin aceite mineral, nitritos ni metales pesados, que aporta gran limpieza de mecanizado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Alkali buffer | Alkanolamine | 0-20% |
| Lubricity agent | Polyether polyol | 0-15% |
| Dispersant | Glycerol | 0-5% |
| Rust inhibitor | Organic acid | 0-8% |
| Diluent | Deionised water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless or yellow-green |
| pH value | 5% / 8.8-9.2 |
| Density@ | 20℃ g/cm3 1.05±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Transparency | Clear |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Rust prevention (5%,18-28℃,cast iron chips2h) | 0grade |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Clear liquid |
| Appearance, 5%wt.Dilution | Visual | Clear liquid |
| pH Value, 5%wt. | SH/T 0298 | 8.8-9.2 |
| Rust Prevention, (Cast Iron, 35°C±2°C, RH>95%; Single Chip24h, Stacked Chips8h) | GB/T 6144 | Grade A |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
| Nitrite, mg/L | Nitrite test strip | None |
Stamping & Deep-Drawing Forming Oils
SD-201SD-201 General-Purpose Forming OilTDSSDSCOA
Technical Overview
Mineral-oil-based process lubricant for metal press forming and deep drawing, fortified with multiple extreme-pressure additives.
Масла для штамповки и глубокой вытяжки с противозадирными и смазывающими присадками для тяжёлых операций формообразования металла.
Aceites de estampación y embutición profunda con aditivos de extrema presión y lubricidad para conformado metálico severo.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | Sulphurised EP additive | 0-30% |
| Oiliness agent | Synthetic ester | 0-30% |
| Rust inhibitor | Sulfonate | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Brown-yellow |
| Kinematic viscosity | @ 40℃ mm²/S 90-120 |
| Flash point | (open cup) ℃ >180 |
| Density@ | 20℃ g/cm3 0.92±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Brown-yellow clear liquid |
| Flash Point, °C | GB/T261 | >180 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 80-120 |
| Weld Load (PD), N | GB/T3142 | > 4900 |
| Mechanical Impurities | GB/T511 | None |
| Water Content | GB/T260 | Trace |
SD-202SD-202 Stainless Steel Forming OilTDSSDSCOA
Technical Overview
Process lubricant for severe press forming and deep drawing with outstanding extreme-pressure anti-weld performance, designed for stainless steel.
Масла для штамповки и глубокой вытяжки с противозадирными и смазывающими присадками для тяжёлых операций формообразования металла.
Aceites de estampación y embutición profunda con aditivos de extrema presión y lubricidad para conformado metálico severo.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | EP additive package | 0-40% |
| Oiliness agent | Synthetic ester | 0-20% |
| Rust inhibitor | Sulfonate | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow |
| Kinematic viscosity | @ 40℃ mm²/S 350-500 |
| Flash point | (open cup) ℃ >200 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Light-yellow to yellow clear liquid |
| Flash Point, °C | GB/T267 | > 200 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 350-500 |
| Weld Load (PD), N | GB3142 | > 6076 |
| Water Content | GB/T260 | Trace |
| Mechanical Impurities | GB/T511 | None |
SD-320SD-320 Rust-Preventive Stamping OilTDSSDSCOA
Technical Overview
Rust-preventive stamping lubricant based on mineral oil and a multi-additive package for press forming operations.
Масла для штамповки и глубокой вытяжки с противозадирными и смазывающими присадками для тяжёлых операций формообразования металла.
Aceites de estampación y embutición profunda con aditivos de extrema presión y lubricidad para conformado metálico severo.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | Sulphurised EP additive | 0-20% |
| Oiliness agent | Synthetic ester | 0-10% |
| Oiliness agent | Vegetable oil/fat | 0-20% |
| Rust inhibitor | Sulfonate | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow |
| Kinematic viscosity | @ 40℃ mm²/S 30-40 |
| Flash point | (open cup) ℃ >180 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Yellow clear liquid |
| Flash Point, °C | GB/T261 | >180 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 30-40 |
| Weld Load (PD), N | GB3142 | >3920 |
SD-920GSD-920G Water-Based Drawing PasteTDSSDSCOA
Technical Overview
Water-soluble drawing paste engineered for demanding stainless steel sheet deep drawing, with strong lubricity and extreme-pressure performance.
Масла для штамповки и глубокой вытяжки с противозадирными и смазывающими присадками для тяжёлых операций формообразования металла.
Aceites de estampación y embutición profunda con aditivos de extrema presión y lubricidad para conformado metálico severo.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Alkali buffer | Alkanolamine | 0-15% |
| Extreme-pressure additive | EP additive package | 0-15% |
| Lubricity agent | Fatty acid ester | 0-10% |
| Thickener | Amide | 0-10% |
| Rust inhibitor | Organic acid | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Paste |
| Colour | White or light yellow |
| pH value | 5% / 8.0-9.0 Solubility / Soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | White-light-yellow paste |
| Storage stability | no discolouration、no separation、homogeneous paste |
| Appearance | Emulsion |
| pH value | 8.0-9.0 |
| Separation stability(Centrifuge test,1500r,30min) | no separation,No phase change |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | White paste |
| Dilution Appearance, 5%wt. | Visual | Emulsion |
| Значение pH | pH meter | 8.0-9.0 |
SD-920SD-920 Water-Based Stamping & Drawing OilTDSSDSCOA
Technical Overview
Water-based stamping and drawing fluid with lubricity, EP and rust inhibitors; free of heavy metals, sodium nitrite and phenols.
Масла для штамповки и глубокой вытяжки с противозадирными и смазывающими присадками для тяжёлых операций формообразования металла.
Aceites de estampación y embutición profunda con aditivos de extrema presión y lubricidad para conformado metálico severo.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | 40-50% |
| Extreme-pressure additive | EP additive package | 10-20% |
| Lubricity agent | Fatty acid amide | 10-20% |
| Surfactant | alcohol ether carboxylic acid | 3-8% |
| Rust inhibitor | Organic acid | 3-8% |
| Deionised water | Deionised water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Brown-yellow or yellow |
| pH value | 5% / 8.8-9.2 |
| Density@ | 20℃ g/cm3 0.98±0.05 Solubility / Soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | >70 |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,10min/ml | ≤2 |
| Corrosion test h (55±2℃full immersion) | Steel strip 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | 0.5 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| pH Value, 5%wt. | pH meter | 8.8-9.2 |
| Rust Prevention, (Cast Iron, 35°C±2°C, Single Chip24h, Stacked Chips8h) | GB/T 6144 | Grade A |
| Corrosion (55°C±2°C), h | Steel strip | GB/T6144 |
| Corrosion (55°C±2°C), h | Copper | GB/T6144 |
| Corrosion (55°C±2°C), h | LY12 aluminum | GB/T6144 |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
Semi-Synthetic & Microemulsion Fluids
SW-020SW-020 Aluminum Wheel Specialty Cutting FluidTDSSDSCOA
Technical Overview
Water-miscible cutting fluid for aluminum wheel hubs with stable emulsion, bacterial resistance, low skin irritation and long service life; nitrite free.
Полусинтетическая микроэмульсионная СОЖ с сочетанием смазывающей способности синтетических растворов и защиты эмульсий.
Fluido semisintético de microemulsión que combina la lubricidad de los sintéticos con la protección de las emulsiones.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Alkali buffer | Alkanolamine | 10-20% |
| Lubricity agent | Fatty acid ester | 0-10% |
| Base oil | Mineral oil | 40-60% |
| Surfactant | alcohol ether carboxylic acid | 0-15% |
| Rust inhibitor | Organic acid | 0-10% |
| Deionised water | Deionised water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Red-brown PH value 5% / 8.4-8.8 |
| Density@ | 20℃ g/cm3 0.95±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.4-8.8 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Corrosion test h (55±2℃full immersion) | Grade 1 Grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | None |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Brown-red clear liquid |
| Foam Tendency (mL/10min) | GB/T6144 | <= 2 |
| pH Value, 5%wt. | pH meter | 8.4-8.8 |
| Nitrite Ion Content | Nitrite test strip | None |
SW-030SW-030 Magnesium Alloy Specialty Cutting FluidTDSSDSCOA
Technical Overview
Microemulsion water-soluble cutting fluid for magnesium alloys with lubricity, rust and non-ferrous corrosion inhibitors; heavy-metal and nitrite free.
Полусинтетическая микроэмульсионная СОЖ с сочетанием смазывающей способности синтетических растворов и защиты эмульсий.
Fluido semisintético de microemulsión que combina la lubricidad de los sintéticos con la protección de las emulsiones.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | 40-50% |
| Alkali buffer | Alkanolamine | 0-10% |
| Lubricity agent | Synthetic ester | 0-10% |
| Surfactant | alcohol ether carboxylic acid | 0-10% |
| Corrosion inhibitor | CompoundCorrosion inhibitor | 0-6% |
| Rust inhibitor | Organic acid | 0-5% |
| Diluent | Water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear-Semi-transparent liquid |
| Colour | Yellow |
| pH value | 5% / 9.3-10.3 |
| Density@ | 20℃ g/cm 3 0.97±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 9.3-10.3 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Corrosion test h (55±2℃full immersion) | Grade 1 Grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | None |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Yellow clear liquid |
| Appearance, 5%wt.Dilution | Visual | Microemulsion |
| pH Value, 5%wt. | pH meter | 9.3-10.3 |
| 5%DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Hard-Water Tolerance, 3000ppm | JB/T7453 | No flocculation or precipitate |
| Magnesium AlloyCorrosion (AZ31B Magnesium, 55°C, 8h) | GB/T 6144 | Grade A |
SW-380SW-380 Semi-Synthetic General-Purpose Cutting FluidTDSSDSCOA
Technical Overview
High-efficiency semi-synthetic water-soluble cutting fluid with a full lubricity, rust-inhibitor, non-ferrous passivator and foam-control package.
Полусинтетическая микроэмульсионная СОЖ с сочетанием смазывающей способности синтетических растворов и защиты эмульсий.
Fluido semisintético de microemulsión que combina la lubricidad de los sintéticos con la protección de las emulsiones.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Corrosion inhibitor | amine carboxylate | 0-10% |
| Alkali buffer | Alkanolamine | 10-20% |
| Lubricity agent | Fatty acid ester | 0-10% |
| Base oil | Mineral oil | 20-40% |
| Surfactant | alcohol ether carboxylic acid | 0-15% |
| Rust inhibitor | Organic acid | 0-10% |
| Diluent | Deionised water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Brown-yellow or yellow PH value 5% / 8.8-9.2 |
| Density@ | 20℃ g/cm3 0.98±0.02 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | 45-50 |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,ml/10min | ≤2 |
| Surface tension,mN/m | ≤40 |
| Corrosion test h (55±2℃full immersion) | Grade 1 Grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | None |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Amber clear liquid |
| Refractometer Reading | Refractometer | 45-50 |
| pH Value, 5%wt. | pH meter | 8.8-9.2 |
| Rust Prevention (Cast Iron, 35°C±2°C, RH>95%Single Chip24h, Stacked Chips8h) | GB/T 6144 | Grade A |
| Corrosion (Copper, 55°C±2°C, 8h) | GB/T 6144 | Grade A |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
| Nitrite, mg/L | Nitrite test strip | None |
SW-F3SW-F3 High-Performance Microemulsion Cutting FluidTDSSDSCOA
Technical Overview
Premium water-soluble microemulsion cutting fluid with balanced lubricity, rust protection, non-ferrous inhibition and foam suppression.
Полусинтетическая микроэмульсионная СОЖ с сочетанием смазывающей способности синтетических растворов и защиты эмульсий.
Fluido semisintético de microemulsión que combina la lubricidad de los sintéticos con la protección de las emulsiones.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow or yellow |
| pH value | 5% / 8.8-9.2 |
| Density@ | 20℃ g/cm 3 0.97±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | >70 |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Corrosion test h (55±2℃full immersion) | Grade 1 Grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| pH Value, 5%wt. | pH meter | 8.8-9.2 |
| Refractometer Reading | Refractometer | > 70 |
| Rust Prevention, 5%wt (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (55°C±2°C), h | Steel strip | GB/T6144 |
| Corrosion (55°C±2°C), h | Copper | GB/T6144 |
| Corrosion (55°C±2°C), h | LY12 aluminum | GB/T6144 |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
SW-F5SW-F5 General-Purpose Microemulsion Cutting FluidTDSSDSCOA
Technical Overview
High-performance general-purpose water-soluble microemulsion cutting fluid for mixed-metal machining cells.
Полусинтетическая микроэмульсионная СОЖ с сочетанием смазывающей способности синтетических растворов и защиты эмульсий.
Fluido semisintético de microemulsión que combina la lubricidad de los sintéticos con la protección de las emulsiones.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Corrosion inhibitor | ammonium carboxylate | 0-10% |
| Alkali buffer | Alkanolamine | 10-15% |
| Lubricity agent | Fatty acid ester | 0-10% |
| Base oil | Mineral oil | 40-60% |
| Surfactant | alcohol ether carboxylic acid | 0-12% |
| Rust inhibitor | Organic acid | 0-10% |
| Diluent | Water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow or yellow PH value 5% / 8.8-9.2 |
| Density@ | 20℃ g/cm 3 0.97±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Content | >71 |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Corrosion test h (55±2℃full immersion) | Grade 1 Grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Yellow clear liquid |
| pH Value, 5%wt. | pH meter | 8.8-9.2 |
| Refractometer Reading | Refractometer | > 71 |
| 5%DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (55°C±2°C), h | Steel strip | GB/T6144 |
| Corrosion (55°C±2°C), h | Copper | GB/T6144 |
| Corrosion (55°C±2°C), h | LY12 aluminum | GB/T6144 |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
SW-F6-55SW-F6-55 Semi-Synthetic Cutting FluidTDSSDSCOA
Technical Overview
Water-soluble semi-synthetic cutting fluid built on selected lubricity, EP and rust-inhibitor additives; free of heavy metals, sodium nitrite and phenols.
Полусинтетическая микроэмульсионная СОЖ с сочетанием смазывающей способности синтетических растворов и защиты эмульсий.
Fluido semisintético de microemulsión que combina la lubricidad de los sintéticos con la protección de las emulsiones.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow or light yellow PH value 5% / 8.8-9.2 |
| Density@ | 20℃ g/cm 3 1.00±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| pH Value, 5%wt. | pH meter | 8.8-9.2 |
| Refractometer Reading | Refractometer | 55-57 |
| 5%DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (55°C±2°C), h | Steel strip | GB/T6144 |
| Corrosion (55°C±2°C), h | Copper | GB/T6144 |
| Corrosion (55°C±2°C), h | LY12 aluminum | GB/T6144 |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
SW-H1SW-H1 Odor-Control Cutting FluidTDSSDSCOA
Technical Overview
Formaldehyde-free, low-odor premium microemulsion cutting fluid with selected lubricity, EP and rust-inhibitor additives.
Полусинтетическая микроэмульсионная СОЖ с сочетанием смазывающей способности синтетических растворов и защиты эмульсий.
Fluido semisintético de microemulsión que combina la lubricidad de los sintéticos con la protección de las emulsiones.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Corrosion inhibitor | ammonium carboxylate | 0-5% |
| Alkali buffer | Alkanolamine | 10-20% |
| Lubricity agent | Fatty acid ester | 0-10% |
| Extreme-pressure additive | EP additive package | 0-10% |
| Base oil | Mineral oil | 30-50% |
| Surfactant | alcohol ether carboxylic acid | 0-8% |
| Rust inhibitor | Organic acid | 0-5% |
| Diluent | Water | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear-Semi-transparent liquid |
| Colour | Yellow PH value 5% / 9.0-9.5 |
| Density@ | 20℃ g/cm 3 0.97±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.8-9.2 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Corrosion test h (55±2℃full immersion) | Grade 1 Grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | None |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| pH Value, 5%wt. | pH meter | 9.0-9.5 |
| 5%DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (55°C±2°C), h | Steel strip | GB/T6144 |
| Corrosion (55°C±2°C), h | Copper | GB/T6144 |
| Corrosion (55°C±2°C), h | LY12 aluminum | GB/T6144 |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
| Nitrite, mg/L | Nitrite test strip | None |
Heat-Transfer Oils
TH-300TH-300 Series Mineral Heat-Transfer OilTDSSDSCOA
Technical Overview
Mineral heat-transfer oil refined by a special process with high-temperature anti-oxidant, anti-scale and anti-coking additives.
Термостойкие теплоносители для закрытых систем косвенного нагрева с высокой окислительной стабильностью.
Fluidos térmicos resistentes a altas temperaturas para sistemas cerrados de calentamiento indirecto, con elevada estabilidad a la oxidación.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Antioxidant | amine salt | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless or light yellow |
| Kinematic viscosity | @ 40℃ mm²/S 27-37 |
| Pour point | ℃ <-9 |
| Flash point | (open cup) ℃ >200 |
| Density@ | 20℃ g/cm3 0.88±0.02 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 27-37 |
| Flash Point, °C | GB/T261 | > 200 |
| Pour Point, °C | GB/T261 | < -9 |
| Corrosion Test, Copper@100°C, 3h | GB/T5096 | Pass |
TH-320TH-320 Series Synthetic Heat-Transfer OilTDSSDSCOA
Technical Overview
Synthetic heat-transfer oil with high-temperature anti-oxidant, anti-scale and anti-coking additives for chemical, agrochemical and textile heating systems.
Термостойкие теплоносители для закрытых систем косвенного нагрева с высокой окислительной стабильностью.
Fluidos térmicos resistentes a altas temperaturas para sistemas cerrados de calentamiento indirecto, con elevada estabilidad a la oxidación.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Antioxidant | amine salt | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless or light yellow |
| Kinematic viscosity | @ 40℃ mm²/S 27-37 |
| Pour point | ℃ <-9 |
| Flash point | (open cup) ℃ >200 |
| Density@ | 20℃ g/cm3 0.88±0.02 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 27-37 |
| Pour Point, °C | GB/T261 | < -9 |
| Corrosion Test, Copper@100°C, 3h | GB/T5096 | Pass |
TH-340TH-340 Series Fully Synthetic High-Efficiency Heat-Transfer OilTDSSDSCOA
Technical Overview
Fully synthetic high-efficiency heat-transfer fluid based on synthetic polyester with premium high-temperature additives for demanding closed-loop systems.
Термостойкие теплоносители для закрытых систем косвенного нагрева с высокой окислительной стабильностью.
Fluidos térmicos resistentes a altas temperaturas para sistemas cerrados de calentamiento indirecto, con elevada estabilidad a la oxidación.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Synthetic oil | Balance |
| Antioxidant | amine salt | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless or light yellow |
| Kinematic viscosity | @ 40℃ mm²/S 20-35 |
| Viscosity index | >95 |
| Flash point | (open cup) ℃ >200 Corrosion test,Copper(100°C,3h) grade 1 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 20-35 |
| Viscosity Index | GB/T2541 | > 95 |
| Flash Point, °C | GB/T261 | >200 |
| Maximum Service Temperature, °C | GB/T23800 | 340 |
| Corrosion Test, Copper@100°C, 3h | SH/T0195 | Pass |
Slideway & Spindle Oils
FDFD Machine-Tool Spindle OilTDSSDSCOA
Technical Overview
Machine-tool spindle oil from high-quality low-viscosity base stocks with detergent, dispersant, anti-wear, anti-oxidant, anti-corrosion and anti-foam additives.
Масла для направляющих и шпинделей станков с противоскачковыми и противоизносными свойствами.
Aceites para guías y husillos de máquina herramienta con propiedades antideslizamiento y antidesgaste.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Lubricity agent | Synthetic ester | 0-10% |
| Antioxidant | amine salt | 0-3% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 1.98-2.42 2.88-3.52 4.14-5.06 6.12-7.48 9.0-11.0 13.5-16.5 19.8-24.2 |
| Pour point | ℃ <-12 |
| Flash point | (open cup) ℃ >70 >80 >90 >115 >140 (100℃,3h) grade 1 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 1.98- 2.42 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 70 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
GG-Series Slideway OilTDSSDSCOA
Technical Overview
Slideway oil based on deeply refined high-viscosity-index base stocks with anti-oxidant, anti-wear and rust inhibitors for precision machine tools.
Масла для направляющих и шпинделей станков с противоскачковыми и противоизносными свойствами.
Aceites para guías y husillos de máquina herramienta con propiedades antideslizamiento y antidesgaste.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Lubricity agent | Anti-wear additive package | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow |
| Kinematic viscosity | @ 40℃ mm²/S 28.8-35.2 41.4-50.6 61.2-74.8 90-110 135-165 198-242 |
| Viscosity index | >90 Report value |
| Pour point | ℃ <-9 <-3 |
| Flash point | (open cup) ℃ >150 >160 >180 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 28.8-35.2 |
| Viscosity Index | GB/T1995 | > 90 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 175 |
| Pour Point, °C | GB/T3535 | < -6 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
Промышленные моющие средства
C-100C-100 Wax RemoverTDSSDSCOA
Technical Overview
Water-based wax remover compounded from surfactants and builders with excellent dispersing, penetrating, cleaning and rust-inhibiting performance.
Промышленные моющие составы для очистки металлических поверхностей, деталей и систем подачи СОЖ.
Limpiadores industriales para superficies metálicas, piezas y circuitos de suministro de refrigerante.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluent | Deionised water | Balance |
| Surfactant | Amide | 0-20% |
| Alkali buffer | Alkanolamine | 0-20% |
| Rust inhibitor | Organic acid | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow or yellow |
| pH value | 5% / 9.60-10.20 Solubility / Fully soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Clear liquid |
| Transparency | Clear |
| pH value | 9.6-10.2 |
| Rust prevention(5%,18-28℃,2h) | cast iron chips 0grade |
| Cleaning performance test,% | 45# ≥98 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Yellow clear liquid |
| pH Value, 5%wt. | pH meter | 9.6-10.2 |
| Cleaning Efficiency, % | JB/T 4323 | >= 98 |
| 5%Rust Prevention (Cast Iron Chips, 18°C-28°C, 2h) | JB/T 9189-2016 | Grade 0 |
C-300ALC-300AL Aluminum Alloy CleanerTDSSDSCOA
Technical Overview
Water-based cleaner with surfactants, builders and specialty corrosion inhibitors for aluminum alloys; powerful penetration and cleaning.
Промышленные моющие составы для очистки металлических поверхностей, деталей и систем подачи СОЖ.
Limpiadores industriales para superficies metálicas, piezas y circuitos de suministro de refrigerante.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Alkali buffer | Alkanolamine | 10-20% |
| Surfactant | Amide | 0-10% |
| Rust inhibitor | Organic acid | 0-10% |
| Builder | Chelate | 0-5% |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Clear liquid |
| Appearance | Clear liquid |
| pH value | 8.6-9.0 |
| Rust prevention(5%,18-28℃,2h) | cast iron chips 0grade |
| Corrosivity (55°C±2°C,8h) | LY12 aluminium Agrade |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Clear liquid |
| Appearance, 5%wt.Dilution | Visual | Clear liquid |
| pH Value, 5%wt. | pH meter | 8.6-9.0 |
| Rust Prevention, 5%wt (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| AluminumCorrosion (LY12 Aluminum, 55°C±2°C, 8h) | GB/T 6144 | Grade A |
C-300LC-300L Low-Foam Spray CleanerTDSSDSCOA
Technical Overview
Low-foam spray cleaner built on premium low-foam surfactants, builders and penetrants, purpose-made for pressure-spray industrial washing machines.
Промышленные моющие составы для очистки металлических поверхностей, деталей и систем подачи СОЖ.
Limpiadores industriales para superficies metálicas, piezas y circuitos de suministro de refrigerante.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Surfactant | Polyether polyol | 0-10% |
| Surfactant | alcohol ether carboxylic acid | 0-10% |
| Alkali buffer | Alkanolamine | 0-20% |
| Corrosion inhibitor | ammonium carboxylate | 0-5% |
| Rust inhibitor | Organic acid | 0-8% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless or light yellow PH value 5% / 9.0-10.0 |
| Density@ | 20℃ g/cm3 1.05±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Clear liquid |
| Transparency | Clear |
| pH value | 9.0-10.0 |
| Rust prevention(5%,18-28℃,2h) | cast iron chips 0grade |
| Cleaning performance test,% | 45# ≥98 |
C-301C-301 Metal CleanerTDSSDSCOA
Technical Overview
Water-based metal cleaner compounded from surfactants and builders with strong dispersing, penetrating, cleaning and rust-inhibiting performance.
Промышленные моющие составы для очистки металлических поверхностей, деталей и систем подачи СОЖ.
Limpiadores industriales para superficies metálicas, piezas y circuitos de suministro de refrigerante.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Surfactant | Amide | 0-10% |
| Alkali buffer | Alkanolamine | 10-20% |
| Corrosion inhibitor | ammonium carboxylate | 0-10% |
| Rust inhibitor | Organic acid | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow or yellow PH value 5% / 9.00-10.00 |
| Density@ | 20℃ g/cm3 1.02±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Clear liquid |
| Transparency | Clear |
| pH value | 9.6-10.2 |
| Rust prevention(5%,18-28℃,2h) | cast iron chips 0grade |
| Cleaning performance test,% | 45# ≥98 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Yellow clear liquid |
| pH Value, 5%wt. | pH meter | 9.6-10.2 |
| Cleaning Efficiency, % | JB/T 4323 | >= 98 |
| 5%Rust Prevention (Cast Iron Chips, 18°C-28°C, 2h) | JB/T 9189-2016 | Grade 0 |
C-305C-305 Degreasing PowderTDSSDSCOA
Technical Overview
Water-based degreasing powder with surfactants, builders and specialty inhibitors for powerful penetration and oil removal.
Промышленные моющие составы для очистки металлических поверхностей, деталей и систем подачи СОЖ.
Limpiadores industriales para superficies metálicas, piezas y circuitos de suministro de refrigerante.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Surfactant | Phosphate | Balance |
| Surfactant | Fatty acid ester | 0-10% |
| Alkali buffer | Alkanolamine | 0-10% |
| Corrosion inhibitor | ammonium carboxylate | 0-5% |
| Deionised water | Deionised water | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | White or light yellow PH value 5% / 8.5-9.5 Solubility / Readily soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | White or light-yellow powder |
| pH value | 8.5-9.5 |
| Cleaning performance test,% | 45# ≥98 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | White to light-yellow powder |
| pH Value, 5%wt. | pH meter | 8.5-9.5 |
| Cleaning Efficiency, % | JB/T 4323 | >= 98 |
C-40C-40 Ultrasonic CleanerTDSSDSCOA
Technical Overview
Water-based ultrasonic cleaner compounded from surfactants and builders with strong penetrating, cleaning and rust-inhibiting performance.
Промышленные моющие составы для очистки металлических поверхностей, деталей и систем подачи СОЖ.
Limpiadores industriales para superficies metálicas, piezas y circuitos de suministro de refrigerante.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Water | Balance |
| Surfactant | Amide | 0-10% |
| Surfactant | Fatty alcohol ether | 0-10% |
| Alkali buffer | Alkanolamine | 0-20% |
| Builder | Chelating agent | 0-5% |
| Rust inhibitor | Organic acid | 0-8% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow |
| pH value | 5% / 9.50-10.50 |
| Density@ | 20℃ g/cm3 1.05±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Clear liquid |
| Transparency | Clear |
| pH value | 9.5-10.5 |
| Corrosion test (90±2℃full immersion,2h) | 45# Agrade |
| Rust prevention(5%,18-28℃,2h) | cast iron chips 0grade |
| Cleaning performance test(70°C±2°C,Immersion3min,Swing washing4min) | 45# No visible oil film or oily residue |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Yellow clear liquid |
| Appearance, 5%wt.Dilution | Visual | Clear liquid |
| pH Value, 5%wt. | pH meter | 9.50-10.50 |
| Rust Prevention (5%, 18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (90°C±2°C, 2h, 45# Steel) | HB5226 | Grade 0 |
| Cleaning Efficiency Test (45# Steel, 70°C±2°C, Immersion3min, Agitated Wash4min) | HB5226 | No visible oil film or residue |
C-400C-400 Rust RemoverTDSSDSCOA
Technical Overview
Specialty liquid rust remover that dissolves oxide scale and carbon deposits while inhibiting attack on the base metal.
Промышленные моющие составы для очистки металлических поверхностей, деталей и систем подачи СОЖ.
Limpiadores industriales para superficies metálicas, piezas y circuitos de suministro de refrigerante.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Surfactant | Fatty alcohol ethoxylate | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless |
| pH value | 5% / <3 |
| Density@ | 20℃ g/cm3 1.10±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Clear liquid |
| Content | 31-33 |
| pH value | <3 |
Q-100Q-100 Grinding CleanerTDSSDSCOA
Technical Overview
Water-soluble polishing and lapping fluid free of sulphur, phosphorus and chlorine, delivering high surface gloss with good degreasing.
Промышленные моющие составы для очистки металлических поверхностей, деталей и систем подачи СОЖ.
Limpiadores industriales para superficies metálicas, piezas y circuitos de suministro de refrigerante.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluent | Deionised water | Balance |
| Surfactant | Amide | 10-20% |
| Surfactant | 0-15% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid Diluted-fluid appearance / Clear-Semi-transparent |
| pH value | 5% / 2-4 Solubility / Fully soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Clear liquid |
| Appearance | Semi-transparent-Clear liquid |
| pH value | 2-4 |
| Solubility | Fully soluble in water |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| 5%wt.Dilution Appearance | Visual | Clear to translucent |
| pH Value, 5%wt. | pH meter | 2-4 |
| Solubility | Fully water-soluble |
FC-039NR-100 Fire-Resistant CleanerTDSSDSCOA
Technical Overview
Fast-drying solvent cleaner with no flash point and no fire hazard, offering moderate solvency and excellent removal of oils and greases.
Промышленные моющие составы для очистки металлических поверхностей, деталей и систем подачи СОЖ.
Limpiadores industriales para superficies metálicas, piezas y circuitos de suministro de refrigerante.
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Colorless clear liquid |
| Flash Point, °C | GB/T3536 | No flash point |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
Industrial Gear Oils
CKDCKD Heavy-Duty Industrial Gear OilTDSSDSCOA
Technical Overview
Heavy-duty industrial gear oil with strong extreme-pressure anti-wear, oxidation, corrosion and demulsibility performance; reduces power loss and extends oil drain intervals.
Масла для промышленных редукторов с противозадирными присадками для тяжелонагруженных зубчатых передач.
Aceites para reductores industriales con aditivos de extrema presión para engranajes muy cargados.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | EP additive package | 0-10% |
| Lubricity agent | Synthetic ester | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow-Yellow |
| Kinematic viscosity | @ 40℃ mm²/S 61.2-74.8 90-110 135-165 198-242 288-352 414-506 612-748 |
| Viscosity index | >90 |
| Flash point | (open cup) ℃ >180 >200 |
| Pour point | ℃ <-12 <-9 <-5 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 61.2-74.8 |
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T3536 | > 180 |
| Viscosity Index | GB/T2541 | > 90 |
| Pour Point, °C | GB/T3535 | < -12 |
| Weld Load (PD), N | GB/T3142 | >= 2450 |
| Water Content, %wt | GB/T260 | Trace |
L-CKCL-CKC Medium-Duty Industrial Gear OilTDSSDSCOA
Technical Overview
Medium-duty industrial gear oil with excellent EP anti-wear, oxidation stability, demulsibility and thermal stability for light-to-medium duty reducers and circulating systems.
Масла для промышленных редукторов с противозадирными присадками для тяжелонагруженных зубчатых передач.
Aceites para reductores industriales con aditivos de extrema presión para engranajes muy cargados.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | EP additive package | 0-10% |
| Lubricity agent | Synthetic ester | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow |
| Flash point | (open cup) ℃ >180 >200 |
| Viscosity index | >90 >85 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 28.8- 35.2 |
| Flash Point, °C | GB/T3536 | > 180 |
| Viscosity Index | GB/T2541 | > 90 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
FC-042Worm Gear OilTDSSDSCOA
Technical Overview
Worm gear oil from deeply refined base stocks with excellent water separation and oxidation stability for power station and heavy circulation systems.
Масла для промышленных редукторов с противозадирными присадками для тяжелонагруженных зубчатых передач.
Aceites para reductores industriales con aditivos de extrema presión para engranajes muy cargados.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | EP additive package | 0-10% |
| Lubricity agent | Synthetic ester | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow |
| Kinematic viscosity | @ 40℃ mm²/S 198-242 288-352 414-506 612-748 |
| Flash point | (open cup) ℃ >200 >220 |
| Viscosity index | >90 (100℃,3h),grade / 1 grade |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 198-242 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 200 |
| Viscosity Index | GB/T1995 | > 90 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
| Pour Point, °C | GB/T3535 | <= -6 |
Anti-Wear & Fire-Resistant Hydraulic Fluids
HGHG Series Alcohol-Type Fire-Resistant Hydraulic FluidTDSSDSCOA
Technical Overview
Glycol-based fire-resistant hydraulic fluid with high-performance anti-wear and anti-foam additives for systems with occasional open-flame exposure.
Противоизносные и огнестойкие гидравлические жидкости для гидросистем высокого давления.
Fluidos hidráulicos antidesgaste y resistentes al fuego para sistemas de alta presión.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | |
| Kinematic viscosity | @ 40℃ mm²/S 41.4-50.6 61.2-74.8 |
| pH value | 5% / 8.0-11.0 |
| Density@ | 20℃ g/cm3 1.068±0.1 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Red clear liquid |
| Kinematic Viscosity (40°C), mm²/S | GB/T265 | 41.4-50.6 |
| Значение pH | pH meter | 8.0-11.0 |
| Pour Point, °C | GB/T3535 | < -30 |
HMHM Series Ashless Anti-Wear Hydraulic OilTDSSDSCOA
Technical Overview
Ashless anti-wear hydraulic oil from deeply refined high-VI base stocks for industrial, marine and mobile hydraulic systems.
Противоизносные и огнестойкие гидравлические жидкости для гидросистем высокого давления.
Fluidos hidráulicos antidesgaste y resistentes al fuego para sistemas de alta presión.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Lubricity agent | Ashless anti-wear additive | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow |
| Kinematic viscosity | @ 40℃ mm²/S 28.8-35.2 41.4-50.6 61.2-74.8 |
| Viscosity index | >95 |
| Pour point | ℃ <-15 <-9 |
| Flash point | (open cup) ℃ >175 >185 >195 (100℃,3h) grade 1 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 28.8-35.2 |
| Viscosity Index | GB/T1995 | > 95 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 175 |
| Pour Point, °C | GB/T3535 | < -15 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
HPHP Series Synthetic Ester Fire-Resistant Hydraulic FluidTDSSDSCOA
Technical Overview
Synthetic ester fire-resistant hydraulic fluid with friction modifiers, anti-oxidants and rust inhibitors for continuous-casting hydraulic systems in steel plants.
Противоизносные и огнестойкие гидравлические жидкости для гидросистем высокого давления.
Fluidos hidráulicos antidesgaste y resistentes al fuego para sistemas de alta presión.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 41.4-50.6 61.2-74.8 |
| Viscosity index | >180 |
| Flash point | (open cup) ℃ >280 >290 |
| Pour point | ℃ <-27 <-25 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 41.4-50.6 |
| Viscosity Index | GB/T1995 | > 180 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 280 |
| Pour Point, °C | GB/T3535 | < -27 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
HVHV Series Low-Temperature Hydraulic OilTDSSDSCOA
Technical Overview
Low-temperature hydraulic oil from deeply refined high-VI base stocks with friction modifiers and anti-oxidants for excellent cold-flow performance.
Противоизносные и огнестойкие гидравлические жидкости для гидросистем высокого давления.
Fluidos hidráulicos antidesgaste y resistentes al fuego para sistemas de alta presión.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | High-VI base oil | Balance |
| Lubricity agent | Anti-wear additive package | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless-Light yellow |
| Kinematic viscosity | @ 40℃ mm²/S 13.5-16.5 19.8-24.2 28.8-35.2 41.4-50.6 61.2-74.8 |
| Viscosity index | >130 >140 |
| Pour point | ℃ <-36 <-33 <-30 |
| Flash point | (open cup) ℃ >125 >175 >180 (100℃,3h) grade 1 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 13.5-16.5 |
| Viscosity Index | GB/T1995 | > 130 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 125 |
| Pour Point, °C | GB/T3535 | < -36 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
Volatile Blanking & Stamping Oils
HF-7035HF-7035 Fast-Drying Blanking & Shearing OilTDSSDSCOA
Technical Overview
Fast-drying blanking oil from low-viscosity volatile mineral oil with oiliness and rust inhibitors for clean, high-quality sheared surfaces.
Быстроиспаряющиеся масла для вырубки и штамповки, не оставляющие плёнки на поверхности.
Aceites volátiles de corte y estampación que no dejan película residual en la superficie.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Hydrotreated light petroleum distillate | Balance |
| Lubricity agent | Synthetic ester | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless |
| Kinematic viscosity | @ 40℃ mm²/S 1.0-2.0 |
| Flash point | (open cup) ℃ >40 |
| Density@ | 20℃ g/cm3 0.76±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T261 | >40 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 1.0-2.0 |
| Corrosion Test, Copper / Steel@50°C, 3h | SH/T0195 | Grade 1 |
HF-7040HF-7040 Volatile Blanking & Shearing OilTDSSDSCOA
Technical Overview
Volatile blanking oil from low-viscosity mineral oil with oiliness and rust inhibitors, offering fast evaporation and strong penetration.
Быстроиспаряющиеся масла для вырубки и штамповки, не оставляющие плёнки на поверхности.
Aceites volátiles de corte y estampación que no dejan película residual en la superficie.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Hydrotreated light petroleum distillate | Balance |
| Lubricity agent | Synthetic ester | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless |
| Kinematic viscosity | @ 40℃ mm²/S 1.0-2.0 |
| Flash point | (open cup) ℃ >40 |
| Density@ | 20℃ g/cm3 0.76±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T261 | >40 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 1.0-2.0 |
| Corrosion Test, Copper / Steel@50°C, 3h | SH/T0195 | Grade 1 |
HF-7060HF-7060 Slow-Drying Volatile Stamping OilTDSSDSCOA
Technical Overview
Slow-drying volatile stamping oil from low-viscosity mineral oil with oiliness and rust inhibitors for controlled evaporation and good surface finish.
Быстроиспаряющиеся масла для вырубки и штамповки, не оставляющие плёнки на поверхности.
Aceites volátiles de corte y estampación que no dejan película residual en la superficie.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless |
| Kinematic viscosity | @ 40℃ mm²/S 1.3-2.0 |
| Flash point | (open cup) ℃ >60 |
| Density@ | 20℃ g/cm3 0.76±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T261 | >60 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 1.3-2.0 |
| Corrosion Test, Copper / Steel@50°C, 3h | SH/T0195 | Grade 1 |
HF-7090HF-7090 Oil-Film Stamping OilTDSSDSCOA
Technical Overview
Oil-film-forming stamping oil from low-viscosity mineral oil with oiliness and rust inhibitors, leaving a protective lubricating film.
Быстроиспаряющиеся масла для вырубки и штамповки, не оставляющие плёнки на поверхности.
Aceites volátiles de corte y estampación que no dejan película residual en la superficie.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Hydrotreated light petroleum distillate | Balance |
| Lubricity agent | Synthetic ester | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless |
| Kinematic viscosity | @ 40℃ mm²/S 2.0-3.5 |
| Flash point | (open cup) ℃ >90 |
| Density@ | 20℃ g/cm3 0.76±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T261 | >90 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 2.0-3.5 |
| Corrosion Test, Copper / Steel@50°C, 3h | SH/T0195 | Grade 1 |
Heat-Treatment Media
QKQK Fast Bright Quenching OilTDSSDSCOA
Technical Overview
Fast bright quenching oil from deeply refined paraffinic base stocks and a proprietary additive package, designed for high-frequency induction hardening.
Закалочные среды и масла для термообработки с контролируемой скоростью охлаждения.
Medios de temple y aceites de tratamiento térmico con velocidad de enfriamiento controlada.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Antioxidant | amine salt | 0-10% |
| Rust inhibitor | Sulfonate | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow or yellow |
| Kinematic viscosity | @40℃ mm²/S 15-40 |
| Flash point | (open cup) ℃ >150 |
| Density@ | 20℃ g/cm3 0.88±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 15-40 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 150 |
| Water Content, %wt | GB/T260 | Trace |
| Characteristic Temperature, °C | GB/T30823 | >= 650 |
| Maximum Cooling Rate, °C/s | GB/T30823 | >= 80 |
| Cooling Rate@300°C, °C/s | GB/T30823 | <= 10 |
QZQZ Vacuum Quenching OilTDSSDSCOA
Technical Overview
Vacuum quenching oil from narrow-cut, highly refined paraffinic mineral oils compounded with functional additives.
Закалочные среды и масла для термообработки с контролируемой скоростью охлаждения.
Medios de temple y aceites de tratamiento térmico con velocidad de enfriamiento controlada.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Brightening agent | Synthetic ester | 0-5% |
| Antioxidant | amine salt | 0-5% |
| Rust inhibitor | Sulfonate | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow or yellow |
| Kinematic viscosity | @40℃ mm²/S 25-35 |
| Flash point | (open cup) ℃ >200 |
| Density@ | 20℃ g/cm3 0.88±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@100°C, cSt | GB/T265 | 25-35 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 200 |
| Water Content, %wt | GB/T260 | Trace |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | <= 1 |
Vacuum Pump Oils
FC-053High/Low-Temperature Vacuum Pump OilTDSSDSCOA
Technical Overview
High/low-temperature vacuum pump oil with low vapour pressure and stable lubricity across wide operating temperature ranges.
Масла для вакуумных насосов с низким давлением насыщенного пара.
Aceites para bombas de vacío con baja presión de vapor saturado.
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 90.0-110.0 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 206 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
Air-Compressor Oils
FC-0543000 Series Light-to-Medium Duty Air-Compressor OilTDSSDSCOA
Technical Overview
Compressor oil from refined mineral oils and premium additives for oil-injected screw, vane and medium/high-pressure reciprocating compressors.
Компрессорные масла для воздушных компрессоров лёгкой, средней и тяжёлой нагрузки.
Aceites para compresores de aire de servicio ligero, medio y pesado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Lubricity agent | Anti-wear additive package | 0-5% |
| Antioxidant | amine salt | 0-3% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 41.4-50.6 61.2-74.8 90-110 |
| Viscosity index | >90 |
| Flash point | (open cup) ℃ >185 >195 >205 |
| Pour point | ℃ <-9 Solubility / Insoluble in water Boiling point ℃ >300 Density g/cm 3 0.88±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 41.4-50.6 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 185 |
| Viscosity Index | GB/T1995 | > 90 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Pour Point (°C) | GB/T3535 | < -9 |
FC-0554000 Series Semi-Synthetic Medium-to-Heavy Duty Air-Compressor OilTDSSDSCOA
Technical Overview
Semi-synthetic compressor oil from highly saturated hydrotreated base stocks and synthetic esters for higher temperature and pressure screw compressors.
Компрессорные масла для воздушных компрессоров лёгкой, средней и тяжёлой нагрузки.
Aceites para compresores de aire de servicio ligero, medio y pesado.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Highly saturated hydrogenated oil | Balance |
| Lubricity agent | Anti-wear additive package | 0-5% |
| Antioxidant | amine salt | 0-3% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 28.8-35.2 41.4-50.6 61.2-74.8 |
| Viscosity index | >90 |
| Flash point | (open cup) ℃ >185 >195 >205 |
| Pour point | ℃ <-12 Solubility / Insoluble in water Boiling point ℃ >300 Density g/cm 3 0.88±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 28.8-35.2 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 185 |
| Viscosity Index | GB/T1995 | > 90 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
| Pour Point (°C) | GB/T3535 | < -9 |
FC-0566000 Series Fully Synthetic Heavy-Duty Air-Compressor OilTDSSDSCOA
Technical Overview
Fully synthetic heavy-duty compressor oil for oil-injected rotary screw compressors operating under high temperature and high pressure.
Компрессорные масла для воздушных компрессоров лёгкой, средней и тяжёлой нагрузки.
Aceites para compresores de aire de servicio ligero, medio y pesado.
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 28.5-35.2 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 220 |
| Viscosity Index | GB/T1995 | > 120 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
| Pour Point (°C) | GB/T3535 | <= -40 |
Neat Cutting Oils
EDM-1EDM-1 Precision EDM OilTDSSDSCOA
Technical Overview
Low-viscosity, low-volatility precision EDM dielectric fluid with excellent cooling and flushing for all electrical-discharge machines.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Hydrorefined petroleum distillate | Balance |
| Antioxidant | amine salt | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless |
| Kinematic viscosity | @ 40℃ mm²/S 1.5-3.5 |
| Flash point | (open cup) ℃ >90 |
| Density@ | 20℃ g/cm3 0.78±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Colorless clear liquid |
| Flash Point, °C | GB/T3536 | >90 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 1.5-3.5 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
| Corrosion@100°C, 3h, Copper | GB/T391 | Grade 1 |
EDM-SEDM-S Synthetic EDM OilTDSSDSCOA
Technical Overview
Synthetic EDM dielectric fluid with low aromatic content, mild odour and low foaming, purpose-designed for electro-erosion machining.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Hydrorefined petroleum distillate | Balance |
| Antioxidant | amine salt | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless |
| Kinematic viscosity | @ 40℃ mm²/S 1.5-3.5 |
| Flash point | (open cup) ℃ >90 |
| Density@ | 20℃ g/cm3 0.78±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Colorless clear liquid |
| Flash Point, °C | GB/T3536 | > 90 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 1.5-3.5 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
| Corrosion@100°C, 3h, Copper | GB/T391 | Grade 1 |
NC-310NC-310 Lapping OilTDSSDSCOA
Technical Overview
Neat lapping oil from refined low-viscosity base stocks and functional additives, delivering superior lubricity and EP performance for high-gloss surfaces.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | Sulphurised EP additive | 0-15% |
| Oiliness agent | Synthetic ester | 0-15% |
| Rust inhibitor | Sulfonate | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow |
| Kinematic viscosity | @ 40℃ mm²/S 10-20 |
| Flash point | (open cup) ℃ >170 |
| Density@ | 20℃ g/cm3 0.85±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T3536 | > 170 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 10-20 |
| Corrosion@100°C, 3h, Steel | SH/T0195 | Grade 1 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
NC-610NC-610 General-Purpose Precision Cutting OilTDSSDSCOA
Technical Overview
General-purpose precision neat cutting oil from EP lubricants, oiliness agents and refined mineral oil for medium-duty high-speed machining of ferrous and non-ferrous metals.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | EP additive package | 0-20% |
| Oiliness agent | Synthetic ester | 0-15% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 10-18 |
| Flash point | (open cup) ℃ >160 |
| Density@ | 20℃ g/cm3 0.85±0.5 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Light-yellow clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 10-18 |
| Flash Point, °C | GB/T3536 | > 160 |
| Corrosion @100°C, 3h | Steel | GB/T5096 |
| Corrosion @100°C, 3h | Copper | GB/T5096 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
NC-620NC-620 General-Purpose Precision Cutting OilTDSSDSCOA
Technical Overview
General-purpose precision neat cutting oil with EP, oiliness and rust inhibitors for medium-to-high speed heavy cutting, including stainless steels.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Lubricity agent | Synthetic ester | 0-20% |
| Extreme-pressure additive | EP additive package | 0-20% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow-Yellow |
| Kinematic viscosity | @ 40℃ mm²/S 15-28 |
| Flash point | (open cup) ℃ >160 |
| Density@ | 20℃ g/cm3 0.85±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T3536 | > 160 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 13-22 |
| Corrosion@100°C, 3h, Copper | GB/T5096 | Grade 1 |
| Mechanical Impurities, % | GB/T511 | None |
| Water Content, % | GB/T260 | Trace |
NC-810TNC-810T Precision Gear Shaving OilTDSSDSCOA
Technical Overview
Precision gear shaving oil from premium base stocks with EP and lubricity additives, engineered for demanding high-lubricity gear machining.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | EP additive package | 0-30% |
| Oiliness agent | Synthetic ester | 0-20% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow-Brown-yellow |
| Kinematic viscosity | @ 40℃ mm²/S 10-25 |
| Flash point | (open cup) ℃ >170 |
| Density@ | 20℃ g/cm3 0.88±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Brown-yellow clear liquid |
| Flash Point, °C | GB/T3536 | > 170 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 10-25 |
| Weld Load (PD), N | GB/T3142 | >= 4900 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
NC-810VNC-810V Deep-Hole Drilling Cutting OilTDSSDSCOA
Technical Overview
Heavy-duty deep-hole drilling oil from multiple EP lubricants, oiliness agents and rust inhibitors with strong lubricity and cooling.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | Sulphurised EP additive | 0-30% |
| Oiliness agent | Synthetic ester | 0-30% |
| Rust inhibitor | Sulfonate | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow |
| Kinematic viscosity | @ 40℃ mm²/S 14-18 |
| Flash point | (open cup) ℃ >140 |
| Density@ | 20℃ g/cm3 0.88±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T3536 | > 140 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 14-18 |
| Extreme-Pressure Property-Weld Load (PD), N | GB/T3142 | > 4900 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
NC-810NC-810 Heavy-Duty Cutting OilTDSSDSCOA
Technical Overview
Heavy-duty neat cutting oil with active EP additives, oiliness agents and rust inhibitors for difficult-to-machine hard materials.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | EP additive package | 0-30% |
| Oiliness agent | Synthetic ester | 0-20% |
| Rust inhibitor | Sulfonate | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow-Brown-yellow |
| Kinematic viscosity | @ 40℃ mm²/S 10-18 |
| Flash point | (open cup) ℃ >140 |
| Density@ | 20℃ g/cm3 0.88±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Brown-yellow clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 10-18 |
| Flash Point, °C | GB/T3536 | > 140 |
| Corrosion@100°C, 3h, Steel | SH/T0195 | Grade 1 |
| Weld Load (PD), N | GB/T3142 | > 4900 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
NC-820NC-820 Heavy-Duty Cutting OilTDSSDSCOA
Technical Overview
Heavy-duty neat cutting oil with active EP additives, oiliness agents and rust inhibitors for difficult-to-machine hard materials.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | Sulphurised EP additive | 0-30% |
| Oiliness agent | Synthetic ester | 0-30% |
| Rust inhibitor | Sulfonate | 0-10% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Brown-yellow |
| Kinematic viscosity | @ 40℃ mm²/S 17-29 |
| Flash point | (open cup) ℃ >160 |
| Density@ | 20℃ g/cm3 0.90±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T3536 | > 160 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 17-29 |
| Corrosion@100°C, 3h, Steel | SH/T0195 | Grade 1 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
NC-920NC-920 Magnesium-Aluminum Alloy Cutting OilTDSSDSCOA
Technical Overview
Colorless, low-odor, low-mist neat cutting oil for magnesium-aluminum alloys, reducing fire risk during magnesium machining.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | Sulphurised EP additive | 0-30% |
| Oiliness agent | Synthetic ester | 0-30% |
| Rust inhibitor | Sulfonate | 0-10% |
| 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow-Yellow |
| Kinematic viscosity | @ 40℃ mm²/S 20-30 |
| Flash point | (open cup) ℃ >170 |
| Density@ | 20℃ g/cm3 0.85±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T3536 | > 170 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 20-30 |
| Corrosion@100°C, 3h, Copper | GB/T5096 | Grade 1 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
NC-V30NC-V30 Minimum-Quantity Spray Machining OilTDSSDSCOA
Technical Overview
MQL spray machining oil from specialty synthetic esters, EP anti-wear agents, stabilizers and rust inhibitors for minimum-quantity lubrication systems.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow |
| Kinematic viscosity | @ 40℃ mm²/S 30-40 |
| Flash point | (open cup) ℃ >260 |
| Density@ | 20℃ g/cm3 0.90±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | SH/T0298 | 30-40 |
| Flash Point, °C | GB/T3536 | > 260 |
| Mechanical Impurities, %wt. | GB/T511 | None |
| Water Content, % | GB/T260 | Trace |
SC-1SC-1 Tapping OilTDSSDSCOA
Technical Overview
Mineral-oil-based neat tapping oil with multiple EP lubricity additives, purpose-built for metal press forming and threading.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Extreme-pressure additive | Sulphurised EP additive | 0-30% |
| Oiliness agent | Synthetic ester | 0-30% |
| Rust inhibitor | Sulfonate | 0-10% |
| 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Red-brown |
| Kinematic viscosity | @ 40℃ mm²/S 80-110 |
| Flash point | (open cup) ℃ >180 |
| Density@ | 20℃ g/cm3 0.90±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T261 | >180 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 80-110 |
| Weld Load (PD), N | GB/T3142 | > 4900 |
| Mechanical Impurities | GB/T511 | None |
| Water Content | GB/T260 | Trace |
NNC-P15 Eco-Friendly Precision Cutting OilTDSSDSCOA
Technical Overview
Eco-friendly precision neat cutting oil from refined mineral oil and premium lubricants for medium-duty machining of moderate-machinability metals.
Масляные СОЖ (чистые режущие масла) для тяжёлой обработки резанием без разбавления водой.
Aceites de corte puros (sin diluir) para mecanizado pesado, sin mezcla con agua.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Oiliness agent | Synthetic ester | 0-20% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 5-10 |
| Flash point | (open cup) ℃ >110 |
| Density@ | 20℃ g/cm3 0.85±0.5 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Flash Point, °C | GB/T3536 | > 110 |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 5-10 |
| Corrosion @100°C, 3h | Steel | GB/T5096 |
| Corrosion @100°C, 3h | Copper | GB/T5096 |
| Mechanical Impurities, %wt | GB/T511 | None |
| Water Content, %wt | GB/T260 | Trace |
Wire EDM Fluids
SW-010SW-010 Wire EDM Working FluidTDSSDSCOA
Technical Overview
High-efficiency water-soluble wire EDM working fluid from EP lubricants, rust inhibitors and surfactants; free of heavy metals, sodium nitrite and phenols.
High-efficiency water-soluble wire EDM working fluid from EP lubricants, rust inhibitors and surfactants; free of heavy metals, sodium nitrite and phenols.
High-efficiency water-soluble wire EDM working fluid from EP lubricants, rust inhibitors and surfactants; free of heavy metals, sodium nitrite and phenols.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Deionised water | Balance |
| Lubricity agent | Fatty acid ester | 0-15% |
| Rust inhibitor | Reaction product of alkanolamines and organic acids | 0-15% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Light yellow PH value 5% / 9.5-11.0 |
| Density@ | 20℃ g/cm3 1.01±0.02 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Transparency | Clear or semi-transparent |
| Refractive index | Report value |
| pH value | 9.5-11.0 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Corrosion test h (55±2℃full immersion) | Grade-1 grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 4 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Clear liquid |
| Appearance, 5%wt.Dilution | Visual | Translucent to clear liquid |
| pH Value, 5%wt. | pH meter | 9.5-11.0 |
| Rust Prevention, (Cast Iron, 35°C±2°C, RH>95%; Single Chip24h, Stacked Chips8h) | GB/T 6144 | Grade A |
| Nitrite, mg/L | Nitrite test strip | None |
SW-011SW-011 Wire EDM Emulsified OilTDSSDSCOA
Technical Overview
Premium wire EDM emulsifiable oil with lubricity and rust inhibitors; free of heavy metals, sodium nitrite and phenols.
Premium wire EDM emulsifiable oil with lubricity and rust inhibitors; free of heavy metals, sodium nitrite and phenols.
Premium wire EDM emulsifiable oil with lubricity and rust inhibitors; free of heavy metals, sodium nitrite and phenols.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Corrosion inhibitor | amine carboxylate | 0-5% |
| Alkali buffer | Alkanolamine | 0-10% |
| Lubricity agent | Fatty acid ester | 0-20% |
| Surfactant | Fatty alcohol ethoxylate | 0-10% |
| Rust inhibitor | Petroleum sulfonate | 0-10% |
| Base oil | Mineral oil | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Red-brown PH value 5% / 9.2-9.6 |
| Density@ | 20℃ g/cm3 0.90±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Phase | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 9.2-9.6 |
| Foam tendency,10min/ml | ≤2 |
| Corrosion test h (55±2℃full immersion) | Steel strip 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | 0.5 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance, Concentrate | Visual | Brown-red clear liquid |
| Appearance, 5%wt.Dilution | Visual | Milky opaque liquid |
| pH Value, 5%wt. | pH meter | 9.2-9.6 |
| Emulsion Stability@15-35°C,24h, Soap | SH/0365 | <= 0.5 |
| Emulsion Stability@15-35°C,24h, Oil | SH/0365 | None |
| Emulsion Rust Prevention@35±2°C, Cast Iron Chips, Single Chip, 48h | GB/T6144 | Grade A |
| Emulsion Rust Prevention@35±2°C, Cast Iron Chips, Stacked Chips, 8h | GB/T6144 | Grade A |
| Emulsion Corrosion Test@55±2°C, Full Immersion, Steel Strip, 24h | GB/T6144 | Grade 0 |
Die-Casting Release Agents
FC-072Low-Pressure Aluminum Alloy Release AgentTDSSDSCOA
Technical Overview
Low-pressure aluminum alloy die-casting release agent for automotive, electronics, motorcycle and aerospace component casting.
Водные и графитовые разделительные составы для литья под давлением.
Desmoldeantes acuosos y grafitados para fundición a presión.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Deionised water | Deionised water | Balance |
| Film-forming agent | High-molecular wax | 0-20% |
| Emulsifier | Non-ionic emulsifier | 0-20% |
| Base oil | Mineral oil | 0-20% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Homogeneous emulsion |
| Colour | White-Slightly yellow |
| pH value | 8.0-9.0 Solubility / Readily soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | White-Light-yellow emulsion |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| pH value | 8.0-9.0 |
| Solid content,% | >25 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Test Item | Specification | |
| Appearance | White to light-yellow emulsion | |
| Solid Content, % | > 25 | |
| pH Value (1:20) | 8.0-9.0 |
FC-073Zinc Alloy Release AgentTDSSDSCOA
Technical Overview
Emulsified zinc alloy die-casting release agent widely used for automotive, motorcycle, aerospace and electrical components.
Водные и графитовые разделительные составы для литья под давлением.
Desmoldeantes acuosos y grafitados para fundición a presión.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Deionised water | Deionised water | 0-5% |
| Non-ionic surfactant | Fatty alcohol ethoxylate | 10-15% |
| Base oil | Mineral oil | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Brown-yellow |
| pH value | 5% / 6.50-8.00 |
| Density@ | 20℃ g/cm3 0.90±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Amber clear liquid |
| Appearance | Emulsion-like Opaque liquid |
| pH value | 7.0-8.0 |
| Solubility@20℃,Tap water | 3minfully dissolved |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Amber clear liquid |
| Appearance, Dilution | Visual | Opaque emulsion |
| pH Value, 5%wt. | pH meter | 7.0-8.0 |
| Solubility@20°C, Tap Water | Fully dissolved within 3 min |
FC-074High-Pressure Aluminum Alloy Release AgentTDSSDSCOA
Technical Overview
High-pressure aluminum alloy die-casting release agent for demanding heavy-duty casting of automotive and electronics components.
Водные и графитовые разделительные составы для литья под давлением.
Desmoldeantes acuosos y grafitados para fundición a presión.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Deionised water | Deionised water | Balance |
| Alkali buffer | Alkanolamine | 0-6% |
| Film-forming agent | High-molecular wax | 15-25% |
| Lubricity agent | Synthetic ester | 0-20% |
| Emulsifier | Non-ionic emulsifier | 10-20% |
| Rust inhibitor | Organic acid salt | 0-10% |
| Base oil | Mineral oil | 0-15% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Homogeneous emulsion |
| Colour | White-Slightly yellow PH value / 8.0-9.0 Solubility / Readily soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Milky white liquid |
| Stability | after dilution with water(100)48no separation after 24 h |
| Solubility |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Test Item | Specification | |
| Appearance | Milky white liquid | |
| Stability | No separation after 48 h at 1:100 dilution | |
| Solubility | Fully soluble |
Rust-Preventive Oils & Inhibitors
P-100VP-100V Water-Soluble Rust PreventiveTDSSDSCOA
Technical Overview
Water-soluble high-efficiency rust inhibitor for in-process, semi-finished and finished ferrous part protection during manufacturing and maintenance.
Water-soluble high-efficiency rust inhibitor for in-process, semi-finished and finished ferrous part protection during manufacturing and maintenance.
Water-soluble high-efficiency rust inhibitor for in-process, semi-finished and finished ferrous part protection during manufacturing and maintenance.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluent | Deionised water | Balance |
| Alkali buffer | Alkanolamine | 0-40% |
| Rust inhibitor | Organic acid | 0-20% |
| Rust inhibitor | Borate ester | 0-20% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless |
| pH value | 5% / 9.2-9.6 Solubility / Readily soluble in water |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Appearance | Clear liquid |
| pH value | 9.2-9.6 |
| Corrosion test h (55±2℃full immersion) | 45# 168 |
| Rust prevention(5%,18-28℃,2h) | cast iron chips 0grade |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Colorless, clear |
| pH Value, 5%wt. | pH meter | 9.2-9.6 |
| 1:40DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (45# Steel, 55±2°CFull Immersion, 168h) | GB/T 6144 | Pass |
| Nitrite, mg/L | Nitrite test strip | None |
P-141P-141 Highly Concentrated Water-Soluble Rust PreventiveTDSSDSCOA
Technical Overview
Highly concentrated water-soluble rust inhibitor from long-chain polycarboxylic acids and organic amines; phosphorus- and boron-free.
Highly concentrated water-soluble rust inhibitor from long-chain polycarboxylic acids and organic amines; phosphorus- and boron-free.
Highly concentrated water-soluble rust inhibitor from long-chain polycarboxylic acids and organic amines; phosphorus- and boron-free.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluted fluid | Water | Balance |
| Alkali buffer | Alkanolamine | 20-50% |
| Rust inhibitor | Organic acid | 20-40% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Semi-transparent-Clear |
| Colour | Brown 1%Diluted fluid PH value / 8.5-9.5 |
| Density@ | 20℃ g/cm3 1.15±0.1 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Semi-transparent-Clear liquid |
| Appearance | Clear liquid |
| pH value | 8.5-9.5 |
| Corrosion test h (55±2℃full immersion) | 45# 168 |
| Rust prevention(5%,18-28℃,2h) | cast iron chips 0grade |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Brown translucent to clear |
| Dilution Appearance, 5%wt. | Visual | Clear |
| pH Value, 5%wt. | pH meter | 8.5-9.5 |
| Rust Prevention (Cast Iron Chips, 2%wt, 18-25°C, 2h) | JB/T9189-2010 | Grade 0, no rust |
| Corrosion (45# Steel, 55±2°CFull Immersion, 168h) | GB/T 6144 | Pass |
| Nitrite, mg/L | Nitrite test strip | None |
P-40P-40 Ultra-Thin Rust-Preventive OilTDSSDSCOA
Technical Overview
Volatile ultra-thin soft-film rust preventive with low odour, good water displacement and strong salt-spray barrier performance.
Volatile ultra-thin soft-film rust preventive with low odour, good water displacement and strong salt-spray barrier performance.
Volatile ultra-thin soft-film rust preventive with low odour, good water displacement and strong salt-spray barrier performance.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Solvent oil | OilHydrotreated light distillate | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 3-7 |
| Flash point | (open cup) ℃ >80 Solubility / Insoluble in water |
| Density@ | 20℃ g/cm3 0.85±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 3-7 |
| Flash Point (Open Cup), °C | GB/T3536 | >70 |
| Drying Performance | SH/T 0063 | Oily |
| Rust Prevention (Salt-Spray Test), 45# Steel, 12h | SH/T0081 | Pass |
P-901P-901 Soft-Film Rust-Preventive OilTDSSDSCOA
Technical Overview
Soft-film rust preventive that displaces fingerprints and water vapour; thin, transparent, low-odour film for ferrous and non-ferrous metals.
Soft-film rust preventive that displaces fingerprints and water vapour; thin, transparent, low-odour film for ferrous and non-ferrous metals.
Soft-film rust preventive that displaces fingerprints and water vapour; thin, transparent, low-odour film for ferrous and non-ferrous metals.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 27-40 |
| Flash point | (open cup) ℃ >170 |
| Density@ | 20℃ g/cm3 0.90±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Brown-yellow clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 27-40 |
| Flash Point, °C | GB/T3536 | >170 |
| Base-Oil Stability@52°C, 72h | Pass | |
| Rust Prevention (Salt-Spray Test), 45# Steel, 24h | SH/T0081 | Pass |
| Corrosion Test@100±2°C, 3h, Copper | GB/T5096 | Grade 1 |
P-902P-902 Soft-Film Rust-Preventive OilTDSSDSCOA
Technical Overview
Soft-film rust preventive with hand-sweat and water-vapour displacement; thin, transparent, low-odour protective film.
Soft-film rust preventive with hand-sweat and water-vapour displacement; thin, transparent, low-odour protective film.
Soft-film rust preventive with hand-sweat and water-vapour displacement; thin, transparent, low-odour protective film.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 27-40 |
| Flash point | (open cup) ℃ >170 |
| Density@ | 20℃ g/cm3 0.90±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Brown-yellow clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 30-40 |
| Flash Point, °C | GB/T3536 | >170 |
| Base-Oil Stability@52°C, 72h | Pass | |
| Rust Prevention (Salt-Spray Test), 45# Steel, 24h | SH/T0081 | Pass |
| Corrosion Test@100±2°C, 3h, Copper | GB/T5096 | Grade 1 |
P-903P-903 Fast-Drying Rust-Preventive OilTDSSDSCOA
Technical Overview
Fast-drying rust preventive based on light distillate and multiple rust inhibitors for applications requiring rapid dry-to-touch.
Fast-drying rust preventive based on light distillate and multiple rust inhibitors for applications requiring rapid dry-to-touch.
Fast-drying rust preventive based on light distillate and multiple rust inhibitors for applications requiring rapid dry-to-touch.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Solvent oil | Hydrocarbon | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 1-3 |
| Flash point | (open cup) ℃ >40 |
| Density@ | 20℃ g/cm3 0.78±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 1.0-3.0 |
| Flash Point (Open Cup), °C | GB/T 261 | >40 |
| Corrosion Test (Copper, 50°C, 3h), ≤2Grade | GB/T 5096 | Pass |
| Salt-Spray Test (45# Steel Panel), >12h | SH/T 0081 | Pass |
P-904P-904 Water-Displacement Rust-Preventive OilTDSSDSCOA
Technical Overview
Water-displacing rust preventive with dehydrating agents for inter-process protection of machined steel parts; strips residual water film.
Water-displacing rust preventive with dehydrating agents for inter-process protection of machined steel parts; strips residual water film.
Water-displacing rust preventive with dehydrating agents for inter-process protection of machined steel parts; strips residual water film.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Solvent oil | Petroleum solvent | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 2.0-4.0 |
| Flash point | (open cup) ℃ >80 |
| Density@ | 20℃ g/cm3 0.78±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 2.0-4.0 |
| Flash Point (Open Cup), °C | GB/T 261 | >70 |
| Drying Performance | SH/T 0063 | Oily |
| Corrosion Test (Copper, 100°C, 3h), ≤2Grade | GB/T 5096 | Pass |
| Salt-Spray Test (45# Steel Panel), >12h | SH/T0081 | Pass |
P-906P-906 Long-Term Storage Wax-Film Rust-Preventive OilTDSSDSCOA
Technical Overview
Long-term wax-film rust preventive from petroleum solvent, wax and inhibitors with outstanding salt-spray and humidity resistance for storage sealing.
Long-term wax-film rust preventive from petroleum solvent, wax and inhibitors with outstanding salt-spray and humidity resistance for storage sealing.
Long-term wax-film rust preventive from petroleum solvent, wax and inhibitors with outstanding salt-spray and humidity resistance for storage sealing.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Diluent | Petroleum solvent | Balance |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Brown-yellow liquid |
| Flash point | (open cup) ℃ >40 Solubility / Insoluble in water |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Colour | Visual | Light brown-yellow liquid |
| Flash Point, °C | GB/T3536 | > 40 |
| Drying Performance | SH/T0063 | Waxy film |
| Low-Temperature Adhesion | SH/T0211 | Pass |
| Water Displacement | SH/T0036 | Pass |
| Rust Prevention (Humidity), h | GB/T2361 | >= 168 |
| Rust Prevention (Salt Spray), h | SH/T0081 | > 48 |
P-907P-907 Hard-Film Rust-Preventive Oil (Golden Yellow)TDSSDSCOA
Technical Overview
Golden-yellow resin-based hard-film rust preventive forming a durable protective coating on metal surfaces.
Golden-yellow resin-based hard-film rust preventive forming a durable protective coating on metal surfaces.
Golden-yellow resin-based hard-film rust preventive forming a durable protective coating on metal surfaces.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid Drying behaviour / Hard film Separation stability / No phase change, no separation Solubility / Insoluble in water |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Brown-yellow clear liquid |
| Drying Performance | SH/T0063 | Hard film |
| Sprayability | SH/T0216 | Continuous film |
| Separation Stability | SH/T0214 | No phase change, no separation |
| Water Content, %wt. | GB/T 260 | None |
| Salt-Spray Test (45# Steel Panel), >24h | SH/T0081 | Pass |
P-9900P-9900 Hard-Film Rust-Preventive Oil (Golden Yellow)TDSSDSCOA
Technical Overview
Golden-yellow resin-based hard-film rust preventive that rapidly forms a tough, visible protective film on metal surfaces.
Golden-yellow resin-based hard-film rust preventive that rapidly forms a tough, visible protective film on metal surfaces.
Golden-yellow resin-based hard-film rust preventive that rapidly forms a tough, visible protective film on metal surfaces.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Dark brown-red liquid Drying behaviour / Hard film Separation stability / No phase change, no separation |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Red-brown translucent to clear liquid |
| Drying Performance | SH/T0063 | Hard film |
| Sprayability | SH/T0216 | Continuous film |
| Separation Stability | SH/T0214 | No phase change, no separation |
| Water Content, %wt. | GB/T 260 | None |
| Salt-Spray Test (45# Steel Panel), >24h | SH/T0081 | Pass |
Minimum-Quantity Lubrication (MQL) Oils
KXD-1102KXD-1102 Minimum-Quantity Lubrication (MQL) OilTDSSDSCOA
Technical Overview
Chlorine-free MQL fluid based on high-lubricity synthetic esters; non-toxic with excellent anti-misting and lubricity for near-dry machining.
Chlorine-free MQL fluid based on high-lubricity synthetic esters; non-toxic with excellent anti-misting and lubricity for near-dry machining.
Chlorine-free MQL fluid based on high-lubricity synthetic esters; non-toxic with excellent anti-misting and lubricity for near-dry machining.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless or light yellow |
| Kinematic viscosity | @ 40℃ mm²/S 20-30 |
| Flash point | (open cup) ℃ >200 |
| Density@ | 20℃ g/cm3 0.90±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T0265 | 20-30 |
| Flash Point, °C | GB/T3536 | > 200 |
| Copper Corrosion (Copper, 100°C, 3h) | GB/T5096 | Grade A |
| Mechanical Impurities, %wt. | GB/T511 | None |
| Water Content, % | GB/T260 | Trace |
KXD-1103KXD-1103 Minimum-Quantity Lubrication (MQL) OilTDSSDSCOA
Technical Overview
Chlorine-free MQL fluid based on high-lubricity synthetic esters; non-toxic with excellent anti-misting and lubricity for near-dry machining.
Chlorine-free MQL fluid based on high-lubricity synthetic esters; non-toxic with excellent anti-misting and lubricity for near-dry machining.
Chlorine-free MQL fluid based on high-lubricity synthetic esters; non-toxic with excellent anti-misting and lubricity for near-dry machining.
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T0265 | 10-20 |
| Flash Point, °C | GB/T3536 | > 200 |
| Copper Corrosion (Copper, 100°C, 3h) | GB/T5096 | Grade A |
| Mechanical Impurities, %wt. | GB/T511 | None |
| Water Content, % | GB/T260 | Trace |
NM-25NM-25 Minimum-Quantity Lubrication (MQL) OilTDSSDSCOA
Technical Overview
MQL fluid from refined mineral oil and EP anti-wear additives, delivering effective lubrication and cooling with minimum-quantity lubrication equipment.
MQL fluid from refined mineral oil and EP anti-wear additives, delivering effective lubrication and cooling with minimum-quantity lubrication equipment.
MQL fluid from refined mineral oil and EP anti-wear additives, delivering effective lubrication and cooling with minimum-quantity lubrication equipment.
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T0265 | 20-30 |
| Flash Point, °C | GB/T3536 | > 200 |
| Copper Corrosion (Copper, 100°C, 3h) | GB/T5096 | Grade A |
| Mechanical Impurities, %wt. | GB/T511 | None |
| Water Content, % | GB/T260 | Trace |
Bio-Based & Biodegradable Fluids
FC-08846 Bio-Based Biodegradable Hydraulic OilTDSSDSCOA
Technical Overview
Ashless zinc-free biodegradable hydraulic oil based on plant-derived fatty acid esters blended in optimized ratios for high renewability.
Ashless zinc-free biodegradable hydraulic oil based on plant-derived fatty acid esters blended in optimized ratios for high renewability.
Ashless zinc-free biodegradable hydraulic oil based on plant-derived fatty acid esters blended in optimized ratios for high renewability.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 41.4-50.6 |
| Viscosity index | ≥180 |
| Pour point | ℃ ≤-24 |
| Flash point | (open cup) ℃ ≥270 |
| Density@ | 20℃ g/cm3 0.92±0.02 Boiling point/Boiling range ℃ >300 Solubility / Insoluble in water, agent、Mineral and synthetic oils |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 41.4-50.6 |
| Viscosity Index | GB/T1995 | >= 180 |
| Cleveland Open-Cup Flash Point, °C | GB/T267 | >= 270 |
| Pour Point, °C | GB/T3535 | <= -24 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Biodegradability, % | OECD 301B | >= 65 |
F8F8 Bio-Based Semi-Synthetic Cutting FluidTDSSDSCOA
Technical Overview
Bio-based semi-synthetic cutting fluid from plant ester base stocks with a synergistic polycarboxylic rust-inhibitor and specialty amine neutralization system; boron-free.
Bio-based semi-synthetic cutting fluid from plant ester base stocks with a synergistic polycarboxylic rust-inhibitor and specialty amine neutralization system; boron-free.
Bio-based semi-synthetic cutting fluid from plant ester base stocks with a synergistic polycarboxylic rust-inhibitor and specialty amine neutralization system; boron-free.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid PH value 5% / 8.5-9.5 |
| Density@ | 20℃ g/cm 3 0.95-1.05 Solubility / Miscible with water in any proportion,forms a semi-transparent microemulsion |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Appearance | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.5-9.5 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Corrosion test h (55±2℃full immersion) | Grade 1 Grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | None |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Concentrate Appearance | Visual | Clear liquid |
| pH Value, 5%wt. | pH meter | 8.5-9.5 |
| 5%DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (55°C±2°C), h | LY12 aluminum | GB/T6144 |
| Corrosion (55°C±2°C), h | Copper | GB/T6144 |
| Biodegradability, % | OECD 301B | >= 60 |
NC-E20NC-E20 Bio-Based Ester-Blend Cutting OilTDSSDSCOA
Technical Overview
New-generation eco-friendly plant-based neat cutting oil from biodegradable synthetic esters with EP, antioxidant and rust-inhibitor additives.
New-generation eco-friendly plant-based neat cutting oil from biodegradable synthetic esters with EP, antioxidant and rust-inhibitor additives.
New-generation eco-friendly plant-based neat cutting oil from biodegradable synthetic esters with EP, antioxidant and rust-inhibitor additives.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Kinematic viscosity | @ 40℃ mm²/S 10-20 |
| Flash point | (open cup) ℃ ≥200 Solubility / Insoluble in water,Soluble in organic solvents and mineral oil |
| Density@ | 20℃ g/cm 3 0.87±0.05 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear |
| Kinematic Viscosity@40°C, cSt | GB/T265 | 10-20 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | >= 200 |
| Weld Load (PD), N | GB/T3142 | >= 3920 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
| Biodegradability, % | OECD 301B | >= 60 |
Eco-Friendly Cutting Fluids
EC-S100EC-S100 Eco-Friendly Cutting FluidTDSSDSCOA
Technical Overview
Bio-stable semi-synthetic general-purpose water-miscible metalworking fluid built on premium fatty acid ester lubrication for extended sump life.
Bio-stable semi-synthetic general-purpose water-miscible metalworking fluid built on premium fatty acid ester lubrication for extended sump life.
Bio-stable semi-synthetic general-purpose water-miscible metalworking fluid built on premium fatty acid ester lubrication for extended sump life.
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Yellow |
| pH value | 5% / 8.5-9.5 |
| Density@ | 20℃ g/cm 3 1.00±0.05 |
Factory Inspection Criteria
| Test item | Acceptance criterion |
|---|---|
| Appearance | Homogeneous clear liquid |
| Storage stability | No discolouration, no separation, homogeneous liquid |
| Appearance | Homogeneous emulsion |
| Refractive index | Report value |
| pH value | 8.5-9.5 |
| Foam tendency,10min/ml | ≤2 |
| Surface tension,mN/m | ≤40 |
| Corrosion test h (55±2℃full immersion) | Grade 1 Grey cast iron 24 |
| Copper | 8 |
| LY12 aluminium | 8 |
| Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h) | Single sheet 24 |
| Stacked sheets | 8 |
| Dilution stability | Oil None |
| Soap | None |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Appearance | Visual | Clear liquid |
| pH Value, 5%wt. | pH meter | 8.5-9.5 |
| 5%DilutionRust Prevention (18-28°C, 2h, Cast Iron Chips) | JB/T9189-2016 | Grade 0, no rust |
| Corrosion (55°C±2°C), h | Cast iron | GB/T6144 |
| Corrosion (55°C±2°C), h | Copper | GB/T6144 |
| Corrosion (55°C±2°C), h | LY12 aluminum | GB/T6144 |
| Foam Tendency, Distilled Water | GB/T 6144 | Foam <= 2 mL after 10 min |
High-Temperature Chain Oils
FC-092220# High-Temperature Chain OilTDSSDSCOA
Technical Overview
High-temperature chain oil from deeply refined base stocks and specialty additives for chains operating continuously up to 230 °C.
Высокотемпературные масла для цепей и конвейерных печей.
Aceites de alta temperatura para cadenas y hornos transportadores.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Mineral oil | Balance |
| Antioxidant | amine salt | 0-10% |
| Anti-wear additive | Anti-wear additive package | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless or light yellow |
| Kinematic viscosity | @ 40℃ mm²/S 198-242 |
| Flash point | (open cup) ℃ >230 |
| Pour point | ℃ <-10 (100℃,3h) grade 1 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 198-242 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 230 |
| Pour Point | GB/T3535 | < -10 |
| Steel Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
CK22CK22 High-Temperature Chain OilTDSSDSCOA
Technical Overview
Synthetic high-temperature chain oil from premium synthetic esters with low volatility, no carbon build-up and no dripping.
Высокотемпературные масла для цепей и конвейерных печей.
Aceites de alta temperatura para cadenas y hornos transportadores.
Composition / Ingredients
| Component | Chemical identity | Content |
|---|---|---|
| Base oil | Synthetic oil | Balance |
| Antioxidant | amine salt | 0-10% |
| Anti-wear additiveagent | Anti-wear additive package | 0-5% |
Physical & Chemical Properties
| Property | Typical value / unit |
|---|---|
| Physical state | Clear liquid |
| Colour | Colourless or light yellow |
| Kinematic viscosity | @ 40℃ mm²/S 180-220 |
| Viscosity index | >150 |
| Flash point | (open cup) ℃ >300 (100℃,3h) grade 1 |
TDS Specifications
| Property | Test method | Typical value |
|---|---|---|
| Kinematic Viscosity@40°C, cSt | GB/T265 | 180-220 |
| Viscosity Index | GB/T1995 | > 150 |
| Cleveland Open-Cup Flash Point, °C | GB/T3536 | > 300 |
| Water Content, %wt | GB/T260 | Trace |
| Mechanical Impurities, %wt | GB/T511 | None |
| Copper Strip Corrosion (100°C, 3h), Grade | GB/T5096 | Grade 1 |
Additional Source Documents
Documents whose model code could not be matched to the 93-product catalogue are listed here so that no source content is omitted.
TQTQ Hydrocarbon cleanerSDS
60006000SeriesFull-synthetic heavy-duty air-compressor oilSDS
Composition / Ingredients
Base oil Synthetic oil Balance; Lubricity agent Anti-wear additive package 0-5%; Antioxidant amine salt 0-3%
KXD-1102KXD-1102 Minimum-quantity lubrication oilSDS
KXD-1103KXD-1103 Minimum-quantity lubrication oilSDS
F6-55Semi-synthetic general-purpose cutting fluidCOA
Factory Inspection Criteria
Appearance: Homogeneous clear liquid; Storage stability: No discolouration, no separation, homogeneous liquid; Content: 55-57; Refractive index: Report value; pH value: 8.8-9.2; Foam tendency,ml/10min: ≤2; Surface tension,mN/m: ≤40; Corrosion test h (55±2℃full immersion): Grade 1 Grey cast iron 24; Copper: 8; LY12 aluminium: 8; Rust-prevention test hGrade-1 grey cast iron (35℃±2℃RI-b95%h): Single sheet 24; Stacked sheets: 8; Dilution stability: Oil None; Soap: None