Industry Solutions

Industry Lubrication Solutions

From "Which lubricant to select" to "How to achieve maximum tool life and finish"

Key Industry Applications

📱

3C Electronics & Phone Middle Frames

Requirement: High-gloss machining, smoke-free & low-mist, mirror surface

3C parts demand spotless surface quality and clean shop environments. Transparent water-based fluids with extreme cooling and anti-color inhibitors are standard.

Recommended Products: SW-300 High-Gloss Fluid, SW-242 Aluminum Fluid, SW-250 General-Purpose, NC-P15 Precision Oil
🚗

Automotive Parts (Wheels & Housings)

Requirement: Anti-discoloration, high surface finish, long sump life

Die-cast and forged aluminum alloys oxidize easily. Formulations with multi-metal inhibitors prevent blackening while maintaining high tool speeds.

Recommended Products: SW-020 Aluminum Wheel Specialty, SW-F5 Microemulsion, NC-620 Precision Cutting Oil, C-300AL Cleaner
🔋

New Energy & Integrated Die Casting

Requirement: Clean release, smooth castings, no post-machining interference

Integrated gigacasting requires thermal stability and zero buildup on dies. Subsequent cleaning and rust protection ensure battery tray cleanliness.

Recommended Products: High-Pressure Release Agent, Aluminum Slag-Removing Agent, C-300L Low-Foam Cleaner, P-40 Ultra-Thin Rust Oil
⚙️

Precision Molds & Cemented Carbide

Requirement: Prevent cobalt leaching, mirror polish, edge protection

Carbide tooling contains cobalt binders. Our synthetic grinding fluids contain anti-cobalt dissolution agents to protect carbide matrices and operator health.

Recommended Products: SW-400 Carbide Grinding Fluid, SW-760 Polishing Fluid, NC-310 Lapping Oil, EDM-1 Precision EDM Oil
🔩

Metal Products & Fasteners

Requirement: High film strength, extreme pressure, burr-free threads

Cold heading, nut tapping, and thread rolling demand resilient boundary lubrication to withstand severe deformation without scoring punches or dies.

Recommended Products: SD-605-80 Cold-Heading Oil, SD-605-120 Warm-Heading Oil, SC-2 Tapping Oil, HF-9090 Stamping Oil
❄️

Electronics & Radiator Heat-Sink Fins

Requirement: Easy degreasing, zero volatile residue, no oxidation

Thin aluminum radiator fins require fast-evaporating stamping fluids or solvent-cleanable formulations to allow seamless soldering and assembly.

Recommended Products: HF-7090 Stamping Oil, Q-100 Grinding Cleaner, TQ Hydrocarbon Cleaner, C-300W Copper Cleaner

Quick Field-Issue Lookup & Troubleshooting

When machining anomalies occur on the plant floor, follow these targeted diagnostic steps.

1. Fluid Bad Odor / Rotten Smell

Causes: Low concentration, tramp oil seal, long weekend downtime, anaerobic bacteria growth.

  • Refractometer check Brix & pH; top up concentrate into recommended zone.
  • Skim surface tramp oil immediately; circulate and aerate fluid.
  • For severe cases, sterilize sump with system cleaner before recharging.

2. Workpiece / Machine Tool Rusting

Causes: Dropped pH (<8.5), concentration too low, high chloride (>10ppm), water hardness drift.

  • Maintain pH in 8.5~9.5 (ferrous) / 7.5~8.5 (non-ferrous).
  • Increase refractometer concentration by 1.5%~2.0%.
  • Check tap/RO water quality; apply inter-process rust-preventive oil (P-40 / P-80).

3. Excessive Sump Foaming

Causes: Ultra-soft water (<50ppm), excessively high concentration, cleaner chemical contamination, pump suction air leaks.

  • Dilute fluid back to target Brix reading.
  • Confirm no alkaline cleaners accidentally leaked into the coolant tank.
  • Inspect pump intake and nozzle velocity; raise coolant sump level.

4. Emulsion Demulsification / Oil Separation

Causes: Extreme hard water buildup, high mineral salt content, mixing incompatible coolants.

  • Never blend mineral-based emulsion with semi-synthetic or synthetic fluids directly.
  • Drain, flush with system cleaner, and refill using filtered water.
  • Deploy oil-water separation equipment to pull out emulsified tramp oils.

5. Aluminum Stains & White Corrosion Spots

Causes: High alkalinity (pH > 9.3) attacking aluminum, missing aluminum passivator, moisture trapping.

  • Switch to dedicated aluminum coolants (SW-242 / SW-020) containing anti-stain inhibitors.
  • Keep pH tightly controlled between 7.8 and 8.8.
  • Blow dry parts with clean compressed air promptly after machining.

6. Short Tool Life & Poor Surface Finish

Causes: Insufficient extreme-pressure (EP) lubrication lubricity, severe tool flank wear or built-up edge.

  • Upgrade from generic emulsion to high-performance microemulsion or neat cutting oil.
  • Increase coolant nozzle pressure directly directed at tool cutting edge.
  • Adjust concentration upwards by 1% to 2% to elevate oil film strength.

Need a Customized Lubrication Audit for Your Facility?

FanChu application engineers are ready to evaluate your workpieces, machining setups, and coolant tanks.

Contact Application Specialists